diff --git a/uim.c b/uim.c
new file mode 100644
index 0000000..53fc88e
--- /dev/null
+++ b/uim.c
@@ -0,0 +1,568 @@
+/*
+ *  User Mode Init manager - For TI shared transport
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation; either version 2 of the License, or
+ *  (at your option) any later version.
+ *
+ *  This program is distributed in the hope that it will be useful,
+ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *  GNU General Public License for more details.
+ *
+ *  You should have received a copy of the GNU General Public License
+ *  along with this program;if not, write to the Free Software
+ *  Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+#include <stdio.h>
+#include <errno.h>
+#include <fcntl.h>
+#include <string.h>
+#include <signal.h>
+#include <sys/ioctl.h>
+#include <termios.h>
+#include <poll.h>
+#include <stdint.h>
+#include <stdlib.h>
+#include <sys/stat.h>
+#include <sys/utsname.h>
+
+#include "uim.h"
+
+/* Maintains the exit state of UIM*/
+static int exiting;
+
+/* UART configuration parameters*/
+int uart_flow_control;
+int cust_baud_rate;
+char uart_dev_name[15];
+unsigned int uart_baud_rate;
+struct termios ti;
+int line_discipline;
+
+/* File descriptor for the UART device*/
+int dev_fd;
+
+/* Maintains the state of N_TI_WL line discipline installation*/
+unsigned char st_state = INSTALL_N_TI_WL;
+unsigned char prev_st_state = UNINSTALL_N_TI_WL;
+
+struct rfkill_event {
+uint32_t idx;
+uint8_t  type;
+uint8_t  op;
+uint8_t  soft, hard;
+} __packed;
+struct rfkill_event rf_event;
+int rfkill_idx;
+
+/*****************************************************************************/
+#ifdef UIM_DEBUG
+/*  Function to Read the firmware version
+ *  module into the system. Currently used for
+ *  debugging purpose, whenever the baud rate is changed
+ */
+void read_firmware_version()
+{
+	int index = 0;
+	char resp_buffer[20] = { 0 };
+	unsigned char buffer[] = { 0x01, 0x01, 0x10, 0x00 };
+
+	UIM_START_FUNC();
+	UIM_VER(" wrote %d bytes", (int)write(dev_fd, buffer, 4));
+	UIM_VER(" reading %d bytes", (int)read(dev_fd, resp_buffer, 15));
+
+	for (index = 0; index < 15; index++)
+		UIM_VER(" %x ", resp_buffer[index]);
+
+	printf("\n");
+}
+#endif
+
+/*****************************************************************************/
+/* Function to read the HCI event from the given file descriptor
+ *
+ * This will parse the response received and returns error
+ * if the required response is not received
+ */
+int read_hci_event(int fd, unsigned char *buf, int size)
+{
+	int remain, rd;
+	int count = 0;
+	int reading = 1;
+	int rd_retry_count = 0;
+	struct timespec tm = {0, 50*1000*1000};
+
+	UIM_START_FUNC();
+
+	UIM_VER(" read_hci_event");
+	if (size <= 0)
+		return -1;
+
+	/* The first byte identifies the packet type. For HCI event packets, it
+	 * should be 0x04, so we read until we get to the 0x04. */
+	while (reading) {
+		rd = read(fd, buf, 1);
+		if (rd <= 0 && rd_retry_count++ < 4) {
+			nanosleep(&tm, NULL);
+			continue;
+		} else if (rd_retry_count >= 4) {
+			return -1;
+		}
+
+		if (buf[0] == RESP_PREFIX)
+			break;
+
+	}
+	count++;
+
+	/* The next two bytes are the event code and parameter total length. */
+	while (count < 3) {
+		rd = read(fd, buf + count, 3 - count);
+		if (rd <= 0)
+			return -1;
+		count += rd;
+	}
+
+	/* Now we read the parameters. */
+	if (buf[2] < (size - 3))
+		remain = buf[2];
+	else
+		remain = size - 3;
+
+	while ((count - 3) < remain) {
+		rd = read(fd, buf + count, remain - (count - 3));
+		if (rd <= 0)
+			return -1;
+		count += rd;
+	}
+
+	return count;
+}
+
+/* Function to read the Command complete event
+ *
+ * This will read the response for the change speed
+ * command that was sent to configure the UART speed
+ * with the custom baud rate
+ */
+static int read_command_complete(int fd, unsigned short opcode)
+{
+	struct command_complete_t resp;
+
+	UIM_START_FUNC();
+
+	UIM_VER(" Command complete started");
+	if (read_hci_event(fd, (unsigned char *)&resp, sizeof(resp)) < 0) {
+		UIM_ERR(" Invalid response");
+		return -1;
+	}
+
+	/* Response should be an event packet */
+	if (resp.uart_prefix != HCI_EVENT_PKT) {
+		UIM_ERR
+			(" Err in response: not an event packet, but 0x%02x!",
+			 resp.uart_prefix);
+		return -1;
+	}
+
+	/* Response should be a command complete event */
+	if (resp.hci_hdr.evt != EVT_CMD_COMPLETE) {
+		/* event must be event-complete */
+		UIM_ERR
+			(" Err in response: not a cmdcomplete evt,but 0x%02x!",
+			 resp.hci_hdr.evt);
+		return -1;
+	}
+
+	if (resp.hci_hdr.plen < 4) {
+		/* plen >= 4 for EVT_CMD_COMPLETE */
+		UIM_ERR(" Err in response: plen is not >= 4, but 0x%02x!",
+				resp.hci_hdr.plen);
+		return -1;
+	}
+
+	if (resp.cmd_complete.opcode != (unsigned short)opcode) {
+		UIM_ERR(" Err in response: opcode is 0x%04x, not 0x%04x!",
+				resp.cmd_complete.opcode, opcode);
+		return -1;
+	}
+
+	UIM_DBG(" Command complete done");
+	return resp.status == 0 ? 0 : -1;
+}
+
+/* Function to set the default baud rate
+ *
+ * The default baud rate of 115200 is set to the UART from the host side
+ * by making a call to this function.This function is also called before
+ * making a call to set the custom baud rate
+ */
+static int set_baud_rate()
+{
+	UIM_START_FUNC();
+
+	tcflush(dev_fd, TCIOFLUSH);
+
+	/* Get the attributes of UART */
+	if (tcgetattr(dev_fd, &ti) < 0) {
+		UIM_ERR(" Can't get port settings");
+		return -1;
+	}
+
+	/* Change the UART attributes before
+	 * setting the default baud rate*/
+	cfmakeraw(&ti);
+
+	ti.c_cflag |= 1;
+	ti.c_cflag |= CRTSCTS;
+
+	/* Set the attributes of UART after making
+	 * the above changes
+	 */
+	tcsetattr(dev_fd, TCSANOW, &ti);
+
+	/* Set the actual default baud rate */
+	cfsetospeed(&ti, B115200);
+	cfsetispeed(&ti, B115200);
+	tcsetattr(dev_fd, TCSANOW, &ti);
+
+	tcflush(dev_fd, TCIOFLUSH);
+	UIM_DBG(" set_baud_rate() done");
+
+	return 0;
+}
+
+/* Function to set the UART custom baud rate.
+ *
+ * The UART baud rate has already been
+ * set to default value 115200 before calling this function.
+ * The baud rate is then changed to custom baud rate by this function*/
+static int set_custom_baud_rate()
+{
+	UIM_START_FUNC();
+
+	struct termios2 ti2;
+
+	UIM_VER(" Changing baud rate to %u, flow control to %u",
+			cust_baud_rate, uart_flow_control);
+
+	/* Flush non-transmitted output data,
+	 * non-read input data or both*/
+	tcflush(dev_fd, TCIOFLUSH);
+
+	/*Set the UART flow control */
+	if (uart_flow_control)
+		ti.c_cflag |= CRTSCTS;
+	else
+		ti.c_cflag &= ~CRTSCTS;
+
+	/*
+	 * Set the parameters associated with the UART
+	 * The change will occur immediately by using TCSANOW
+	 */
+	if (tcsetattr(dev_fd, TCSANOW, &ti) < 0) {
+		UIM_ERR(" Can't set port settings");
+		return -1;
+	}
+
+	tcflush(dev_fd, TCIOFLUSH);
+
+	/*Set the actual baud rate */
+	ioctl(dev_fd, TCGETS2, &ti2);
+	ti2.c_cflag &= ~CBAUD;
+	ti2.c_cflag |= BOTHER;
+	ti2.c_ospeed = cust_baud_rate;
+	ioctl(dev_fd, TCSETS2, &ti2);
+
+	UIM_DBG(" set_custom_baud_rate() done");
+	return 0;
+}
+
+/*
+ * Handling the Signals sent from the Kernel Init Manager.
+ * After receiving the signals, configure the baud rate, flow
+ * control and Install the N_TI_WL line discipline
+ */
+int st_sig_handler(int signo)
+{
+	int ldisc, len;
+	struct uim_speed_change_cmd cmd;
+
+	UIM_START_FUNC();
+
+	/* Raise a signal after when UIM is killed.
+	 * This will exit UIM, and remove the inserted kernel
+	 * modules
+	 */
+	if (signo == SIGINT) {
+		UIM_DBG(" Exiting. . .");
+		exiting = 1;
+		return -1;
+	}
+
+	/* Install the line discipline when the signal is received by UIM.
+	 * Whenever the first protocol tries to register with the ST core, the
+	 * ST KIM will send a signal SIGUSR2 to the UIM to install the N_TI_WL
+	 * line discipline and do the host side UART configurations.
+	 *
+	 * On failure, ST KIM's line discipline installation times out, and the
+	 * relevant protocol register fails
+	 */
+	if (st_state == INSTALL_N_TI_WL) {
+		UIM_VER(" signal received, opening %s", uart_dev_name);
+		dev_fd = open(uart_dev_name, O_RDWR);
+		if (dev_fd < 0) {
+			UIM_ERR(" Can't open %s", uart_dev_name);
+			return -1;
+		}
+		/*
+		 * Set only the default baud rate.
+		 * This will set the baud rate to default 115200
+		 */
+		if (set_baud_rate() < 0) {
+			UIM_ERR(" set_baudrate() failed");
+			close(dev_fd);
+			return -1;
+		}
+
+		fcntl(dev_fd, F_SETFL, fcntl(dev_fd, F_GETFL) | O_NONBLOCK);
+		/* Set only thecustom baud rate */
+		if (cust_baud_rate) {
+
+			/* Forming the packet for Change speed command */
+			cmd.uart_prefix = HCI_COMMAND_PKT;
+			cmd.hci_hdr.opcode = HCI_HDR_OPCODE;
+			cmd.hci_hdr.plen = sizeof(unsigned long);
+			cmd.speed = cust_baud_rate;
+
+			/* Writing the change speed command to the UART
+			 * This will change the UART speed at the controller
+			 * side
+			 */
+			UIM_VER(" Setting speed to %d", cust_baud_rate);
+			len = write(dev_fd, &cmd, sizeof(cmd));
+			if (len < 0) {
+				UIM_ERR(" Failed to write speed-set command");
+				close(dev_fd);
+				return -1;
+			}
+
+			/* Read the response for the Change speed command */
+			if (read_command_complete(dev_fd, HCI_HDR_OPCODE) < 0) {
+				close(dev_fd);
+				return -1;
+			}
+
+			UIM_VER(" Speed changed to %d", cust_baud_rate);
+
+			/* Set the actual custom baud rate at the host side */
+			if (set_custom_baud_rate() < 0) {
+				UIM_ERR(" set_custom_baud_rate() failed");
+				close(dev_fd);
+
+				return -1;
+			}
+#ifdef UIM_DEBUG
+			read_firmware_version();
+#endif
+		}
+
+		/* After the UART speed has been changed, the IOCTL is
+		 * is called to set the line discipline to N_TI_WL
+		 */
+		ldisc = line_discipline;
+		if (ioctl(dev_fd, TIOCSETD, &ldisc) < 0) {
+			UIM_ERR(" Can't set line discipline");
+			close(dev_fd);
+			return -1;
+		}
+
+		UIM_DBG(" Installed N_TI_WL Line displine");
+	} else {
+		/* UNINSTALL_N_TI_WL - When the Signal is received from KIM */
+		/* closing UART fd */
+		UIM_DBG(" Uninstalled N_TI_WL Line displine");
+		close(dev_fd);
+	}
+	prev_st_state = st_state;
+	return 0;
+}
+
+int remove_modules()
+{
+	int err = 0;
+
+	/*Remove the Shared Transport */
+	UIM_VER(" Removing st_drv ");
+
+	if (system("rmmod st_drv") != 0) {
+		UIM_ERR(" Error removing st_drv module");
+		err = -1;
+	} else {
+		UIM_DBG(" Removed st_drv module ");
+	}
+
+	return err;
+}
+
+
+int change_rfkill_perms(void)
+{
+	int fd, id, sz;
+	char path[64];
+	char buf[16];
+	for (id = 0; id < 50; id++) {
+		snprintf(path, sizeof(path),
+			"/sys/class/rfkill/rfkill%d/type", id);
+		fd = open(path, O_RDONLY);
+		if (fd < 0) {
+			UIM_DBG("open(%s) failed: %s (%d)\n",
+				path, strerror(errno), errno);
+			continue;
+		}
+		sz = read(fd, &buf, sizeof(buf));
+		close(fd);
+		if (sz >= 9 && memcmp(buf, "bluetooth", 9) == 0) {
+			UIM_DBG("found bluetooth rfkill entry @ %d\n", id);
+			rfkill_idx = id;
+			break;
+		}
+	}
+	if (id == 50)
+		return -1;
+
+	sz = chmod(path, 0660);
+	if (sz < 0) {
+		UIM_ERR("change mode failed for %s (%d)\n", path, errno);
+		return -1;
+	}
+	UIM_DBG("changed permissions for %s(%d)\n", path, sz);
+	/* end of change_perms */
+
+	return 0;
+}
+/*****************************************************************************/
+int main(int argc, char *argv[])
+{
+	int st_fd, err;
+	char buf[20] = { 0 };
+	struct sigaction sa;
+	struct stat file_stat;
+	struct utsname name;
+
+	struct pollfd p;
+	sigset_t sigs;
+
+	UIM_START_FUNC();
+	err = 0;
+
+	/* Parse the user input */
+	if (argc == 5) {
+		strcpy(uart_dev_name, argv[1]);
+		uart_baud_rate = atoi(argv[2]);
+		uart_flow_control = atoi(argv[3]);
+		line_discipline = atoi(argv[4]);
+
+		/* Depending upon the baud rate value, differentiate
+		 * the custom baud rate and default baud rate
+		 */
+		switch (uart_baud_rate) {
+		case 115200:
+			UIM_VER(" Baudrate 115200");
+			break;
+		case 9600:
+		case 19200:
+		case 38400:
+		case 57600:
+		case 230400:
+		case 460800:
+		case 500000:
+		case 576000:
+		case 921600:
+		case 1000000:
+		case 1152000:
+		case 1500000:
+		case 2000000:
+		case 2500000:
+		case 3000000:
+		case 3500000:
+		case 3686400:
+		case 4000000:
+			cust_baud_rate = uart_baud_rate;
+			UIM_VER(" Baudrate %d", cust_baud_rate);
+			break;
+		default:
+			UIM_ERR(" Inavalid Baud Rate");
+			break;
+		}
+	} else {
+		UIM_ERR(" Invalid arguments");
+		UIM_ERR(" Usage: uim [Uart device] [Baud rate] \
+				[Flow control] [Line discipline]");
+		return -1;
+	}
+
+	if (system("modprobe st_drv") != 0) {
+		UIM_ERR(" Error inserting st_drv module");
+		return -1;
+	} else {
+		UIM_DBG(" Inserted st_drv module");
+	}
+
+
+	if (change_rfkill_perms() < 0) {
+		/* possible error condition */
+		UIM_ERR("rfkill not enabled in st_drv - \
+				BT on from UI might fail\n");
+	}
+
+	st_fd = open("/dev/rfkill", O_RDONLY);
+
+	p.fd = st_fd;
+	p.events = POLLERR | POLLHUP | POLLOUT | POLLIN;
+
+	sigfillset(&sigs);
+	sigdelset(&sigs, SIGCHLD);
+	sigdelset(&sigs, SIGPIPE);
+	sigdelset(&sigs, SIGTERM);
+	sigdelset(&sigs, SIGINT);
+	sigdelset(&sigs, SIGHUP);
+
+RE_POLL:
+	while (!exiting) {
+		p.revents = 0;
+		err = ppoll(&p, 1, NULL, &sigs);
+		if (err < 0 && errno == EINTR)
+			continue;
+		if (err)
+			break;
+	}
+	if (!exiting) {
+		err = read(st_fd, &rf_event, sizeof(rf_event));
+		UIM_DBG("rf_event: %d, %d, %d, %d, %d\n", rf_event.idx,
+			rf_event.type, rf_event.op , rf_event.hard,
+			rf_event.soft);
+		if ((rf_event.op == 2) &&
+			(rf_event.idx == rfkill_idx)) {
+			if (rf_event.hard == 1)
+				st_state = UNINSTALL_N_TI_WL;
+			else
+				st_state = INSTALL_N_TI_WL;
+
+			if (prev_st_state != st_state)
+				st_sig_handler(SIGUSR2);
+		}
+		goto RE_POLL;
+	}
+
+	if (remove_modules() < 0) {
+		UIM_ERR(" Error removing modules ");
+		close(st_fd);
+		return -1;
+	}
+
+	close(st_fd);
+	return 0;
+}
diff --git a/uim.h b/uim.h
new file mode 100644
index 0000000..fff0ff8
--- /dev/null
+++ b/uim.h
@@ -0,0 +1,140 @@
+/*
+ *  User Mode Init manager - For shared transport
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation; either version 2 of the License, or
+ *  (at your option) any later version.
+ *
+ *  This program is distributed in the hope that it will be useful,
+ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *  GNU General Public License for more details.
+ *
+ *  You should have received a copy of the GNU General Public License
+ *  along with this program;if not, write to the Free Software
+ *  Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#ifndef UIM_H
+#define UIM_H
+
+/* Paramaters to set the baud rate*/
+#define  FLOW_CTL	0x0001
+#define  BOTHER		0x00001000
+#define  ARM_NCCS	19
+
+#ifndef TCGETS2
+#define TCGETS2      _IOR('T', 0x2A, struct termios2)
+#endif
+
+#ifndef TCSETS2
+#define TCSETS2      _IOW('T', 0x2B, struct termios2)
+#endif
+
+/*HCI Command and Event information*/
+#define HCI_HDR_OPCODE  0xff36
+#define RESP_PREFIX	0x04
+#define MAX_TRY		10
+
+/* HCI Packet types */
+#define HCI_COMMAND_PKT		0x01
+#define HCI_EVENT_PKT		0x04
+
+/* HCI command macros*/
+#define HCI_EVENT_HDR_SIZE      2
+#define HCI_COMMAND_HDR_SIZE    3
+
+/* HCI event macros*/
+#define EVT_CMD_COMPLETE_SIZE	3
+#define EVT_CMD_STATUS_SIZE	4
+#define EVT_CMD_COMPLETE	0x0E
+#define EVT_CMD_STATUS		0x0F
+
+#define VERBOSE
+/*Debug logs*/
+#define UIM_ERR(fmt, arg...)  printf("uim:"fmt"\n" , ##arg)
+#if defined(UIM_DEBUG)		/* limited debug messages */
+#define UIM_START_FUNC()      printf("uim: Inside %s", __func__)
+#define UIM_DBG(fmt, arg...)  printf("uim:"fmt"\n" , ## arg)
+#define UIM_VER(fmt, arg...)
+#elif defined(VERBOSE)		/* very verbose */
+#define UIM_START_FUNC()      printf("uim: Inside %s", __func__)
+#define UIM_DBG(fmt, arg...)  printf("uim:"fmt"\n" , ## arg)
+#define UIM_VER(fmt, arg...)  printf("uim:"fmt"\n" , ## arg)
+#else /* error msgs only */
+#define UIM_START_FUNC()
+#define UIM_DBG(fmt, arg...)
+#define UIM_VER(fmt, arg...)
+#endif
+
+/*Termios2 structure for setting the Custom baud rate*/
+struct termios2 {
+	tcflag_t c_iflag;	/* input mode flags */
+	tcflag_t c_oflag;	/* output mode flags */
+	tcflag_t c_cflag;	/* control mode flags */
+	tcflag_t c_lflag;	/* local mode flags */
+	cc_t c_line;		/* line discipline */
+	cc_t c_cc[ARM_NCCS];	/* control characters */
+	speed_t c_ispeed;	/* input speed */
+	speed_t c_ospeed;	/* output speed */
+};
+
+/* HCI command header*/
+struct hci_command_hdr {
+	uint16_t        opcode;         /* OCF & OGF */
+	uint8_t         plen;
+} __attribute__ ((packed));
+
+/* HCI event header*/
+struct hci_event_hdr {
+	uint8_t         evt;
+	uint8_t         plen;
+} __attribute__ ((packed));
+
+/* HCI command complete event*/
+struct evt_cmd_complete {
+	uint8_t         ncmd;
+	uint16_t        opcode;
+} __attribute__ ((packed));
+
+/* HCI event status*/
+struct evt_cmd_status {
+	uint8_t         status;
+	uint8_t         ncmd;
+	uint16_t        opcode;
+} __attribute__ ((packed));
+
+/* HCI Event structure to set the cusrom baud rate*/
+struct command_complete_t {
+	uint8_t uart_prefix;
+	struct hci_event_hdr hci_hdr;
+	struct evt_cmd_complete cmd_complete;
+	uint8_t status;
+	uint8_t data[16];
+} __attribute__ ((packed));
+
+/* HCI Command structure to set the cusrom baud rate*/
+struct uim_speed_change_cmd {
+	uint8_t uart_prefix;
+	struct hci_command_hdr hci_hdr;
+	uint32_t speed;
+} __attribute__ ((packed));
+
+/* Signal received from KIM will install line discipline at first,
+ * the next signal received from KIM will un-install the
+ * line discipline*/
+enum {
+	/* expecting signal from KIM to setup uart fd for ST */
+	INSTALL_N_TI_WL,
+
+	/* expecting signal from KIM to close uart fd */
+	UNINSTALL_N_TI_WL,
+};
+
+/* Functions to insert and remove the kernel modules from the system*/
+extern int init_module(void *, unsigned int, const char *);
+extern int delete_module(const char *, unsigned int);
+extern int load_file(const char *, unsigned int *);
+
+#endif /* UIM_H */
diff --git a/uim.spec b/uim.spec
new file mode 100644
index 0000000..ac1f0fd
--- /dev/null
+++ b/uim.spec
@@ -0,0 +1,58 @@
+# 
+# Do not Edit! Generated by:
+# spectacle version 0.15
+# 
+# >> macros
+# << macros
+
+Name:       uim
+Summary:    User Mode Initialization Manager
+Version:    0.1
+Release:    1
+Group:      System/Daemons
+License:    GPLv2+
+URL:        http://dev.omapzoom.org
+Source0:    uim.tgz
+
+%description
+User Mode Init manager - For TI shared transport drivers    
+
+
+
+
+%prep
+%setup -q -n %{name}
+
+# >> setup
+# << setup
+
+%build
+# >> build pre
+# << build pre
+
+%configure --disable-static
+make %{?jobs:-j%jobs}
+
+# >> build post
+# << build post
+%install
+rm -rf %{buildroot}
+# >> install pre
+# << install pre
+%make_install
+
+# >> install post
+# << install post
+
+
+
+
+
+
+%files
+%defattr(-,root,root,-)
+%{_bindir}/uim
+# >> files
+# << files
+
+
diff --git a/uim.tgz b/uim.tgz
new file mode 100644
index 0000000..813453f
--- /dev/null
+++ b/uim.tgz
Binary files differ
diff --git a/uim.yaml b/uim.yaml
new file mode 100644
index 0000000..5561c78
--- /dev/null
+++ b/uim.yaml
@@ -0,0 +1,18 @@
+Name: uim 
+Summary: User Mode Initialization Manager
+Version: 0.1
+Release: 1
+Group: System/Daemons
+License: GPLv2+
+URL: http://dev.omapzoom.org
+Description: |
+    User Mode Init manager - For TI shared transport drivers    
+Sources:
+    - uim.tgz
+Configure: configure
+Files:
+    - "%{_bindir}/uim"
+
+
+
+