[ARM] 4304/1: removes the unnecessary bit number from CKENnn_XXXX
This patch removes the unnecessary bit number from CKENnn_XXXX
definitions for PXA, so that
CKEN0_PWM0 --> CKEN_PWM0
CKEN1_PWM1 --> CKEN_PWM1
...
CKEN24_CAMERA --> CKEN_CAMERA
The reasons for the change of these defitions are:
1. they do not scale - they are currently valid for pxa2xx, but
definitely not valid for pxa3xx, e.g., pxa3xx has bit 3 for camera
instead of bit 24
2. they are unnecessary - the peripheral name within the definition
has already announced its usage, we don't need those bit numbers
to know which peripheral we are going to enable/disable clock for
3. they are inconvenient - think about this: a driver programmer
for pxa has to remember which bit in the CKEN register to turn
on/off
Another change in the patch is to make the definitions equal to its
clock bit index, so that
#define CKEN_CAMERA (24)
instead of
#define CKEN_CAMERA (1 << 24)
this change, however, will add a run-time bit shift operation in
pxa_set_cken(), but the benefit of this change is that it scales
when bit index exceeds 32, e.g., pxa3xx has two registers CKENA
and CKENB, totally 64 bit for this, suppose CAMERA clock enabling
bit is CKENB:10, one can simply define CKEN_CAMERA to be (32 + 10)
and so that pxa_set_cken() need minimum change to adapt to that.
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
diff --git a/Documentation/spi/pxa2xx b/Documentation/spi/pxa2xx
index f9717fe..215e3b8 100644
--- a/Documentation/spi/pxa2xx
+++ b/Documentation/spi/pxa2xx
@@ -62,7 +62,7 @@
static struct pxa2xx_spi_master pxa_nssp_master_info = {
.ssp_type = PXA25x_NSSP, /* Type of SSP */
- .clock_enable = CKEN9_NSSP, /* NSSP Peripheral clock */
+ .clock_enable = CKEN_NSSP, /* NSSP Peripheral clock */
.num_chipselect = 1, /* Matches the number of chips attached to NSSP */
.enable_dma = 1, /* Enables NSSP DMA */
};
diff --git a/arch/arm/mach-pxa/generic.c b/arch/arm/mach-pxa/generic.c
index b8cb79f..64b08b7 100644
--- a/arch/arm/mach-pxa/generic.c
+++ b/arch/arm/mach-pxa/generic.c
@@ -164,9 +164,9 @@
local_irq_save(flags);
if (enable)
- CKEN |= clock;
+ CKEN |= (1 << clock);
else
- CKEN &= ~clock;
+ CKEN &= ~(1 << clock);
local_irq_restore(flags);
}
diff --git a/arch/arm/mach-pxa/lpd270.c b/arch/arm/mach-pxa/lpd270.c
index 8e27a64..e309766 100644
--- a/arch/arm/mach-pxa/lpd270.c
+++ b/arch/arm/mach-pxa/lpd270.c
@@ -234,7 +234,7 @@
{
if (on) {
pxa_gpio_mode(GPIO16_PWM0_MD);
- pxa_set_cken(CKEN0_PWM0, 1);
+ pxa_set_cken(CKEN_PWM0, 1);
PWM_CTRL0 = 0;
PWM_PWDUTY0 = 0x3ff;
PWM_PERVAL0 = 0x3ff;
@@ -242,7 +242,7 @@
PWM_CTRL0 = 0;
PWM_PWDUTY0 = 0x0;
PWM_PERVAL0 = 0x3FF;
- pxa_set_cken(CKEN0_PWM0, 0);
+ pxa_set_cken(CKEN_PWM0, 0);
}
}
diff --git a/arch/arm/mach-pxa/lubbock.c b/arch/arm/mach-pxa/lubbock.c
index 055de7f..6377b2e 100644
--- a/arch/arm/mach-pxa/lubbock.c
+++ b/arch/arm/mach-pxa/lubbock.c
@@ -220,7 +220,7 @@
static struct pxa2xx_spi_master pxa_ssp_master_info = {
.ssp_type = PXA25x_SSP,
- .clock_enable = CKEN3_SSP,
+ .clock_enable = CKEN_SSP,
.num_chipselect = 0,
};
diff --git a/arch/arm/mach-pxa/mainstone.c b/arch/arm/mach-pxa/mainstone.c
index 56d94d8..ed99a81 100644
--- a/arch/arm/mach-pxa/mainstone.c
+++ b/arch/arm/mach-pxa/mainstone.c
@@ -266,7 +266,7 @@
{
if (on) {
pxa_gpio_mode(GPIO16_PWM0_MD);
- pxa_set_cken(CKEN0_PWM0, 1);
+ pxa_set_cken(CKEN_PWM0, 1);
PWM_CTRL0 = 0;
PWM_PWDUTY0 = 0x3ff;
PWM_PERVAL0 = 0x3ff;
@@ -274,7 +274,7 @@
PWM_CTRL0 = 0;
PWM_PWDUTY0 = 0x0;
PWM_PERVAL0 = 0x3FF;
- pxa_set_cken(CKEN0_PWM0, 0);
+ pxa_set_cken(CKEN_PWM0, 0);
}
}
diff --git a/arch/arm/mach-pxa/pxa27x.c b/arch/arm/mach-pxa/pxa27x.c
index 74eeada..c64bab4 100644
--- a/arch/arm/mach-pxa/pxa27x.c
+++ b/arch/arm/mach-pxa/pxa27x.c
@@ -140,9 +140,9 @@
extern void pxa_cpu_resume(void);
if (state == PM_SUSPEND_STANDBY)
- CKEN = CKEN22_MEMC | CKEN9_OSTIMER | CKEN16_LCD |CKEN0_PWM0;
+ CKEN = CKEN_MEMC | CKEN_OSTIMER | CKEN_LCD | CKEN_PWM0;
else
- CKEN = CKEN22_MEMC | CKEN9_OSTIMER;
+ CKEN = CKEN_MEMC | CKEN_OSTIMER;
/* ensure voltage-change sequencer not initiated, which hangs */
PCFR &= ~PCFR_FVC;
diff --git a/arch/arm/mach-pxa/ssp.c b/arch/arm/mach-pxa/ssp.c
index 6cc2027..71766ac 100644
--- a/arch/arm/mach-pxa/ssp.c
+++ b/arch/arm/mach-pxa/ssp.c
@@ -52,13 +52,13 @@
*/
static const struct ssp_info_ ssp_info[PXA_SSP_PORTS] = {
#if defined (CONFIG_PXA27x)
- {IRQ_SSP, CKEN23_SSP1},
- {IRQ_SSP2, CKEN3_SSP2},
- {IRQ_SSP3, CKEN4_SSP3},
+ {IRQ_SSP, CKEN_SSP1},
+ {IRQ_SSP2, CKEN_SSP2},
+ {IRQ_SSP3, CKEN_SSP3},
#else
- {IRQ_SSP, CKEN3_SSP},
- {IRQ_NSSP, CKEN9_NSSP},
- {IRQ_ASSP, CKEN10_ASSP},
+ {IRQ_SSP, CKEN_SSP},
+ {IRQ_NSSP, CKEN_NSSP},
+ {IRQ_ASSP, CKEN_ASSP},
#endif
};
diff --git a/drivers/i2c/busses/i2c-pxa.c b/drivers/i2c/busses/i2c-pxa.c
index 11c7477..4443d3b 100644
--- a/drivers/i2c/busses/i2c-pxa.c
+++ b/drivers/i2c/busses/i2c-pxa.c
@@ -887,14 +887,14 @@
pxa_gpio_mode(GPIO117_I2CSCL_MD);
pxa_gpio_mode(GPIO118_I2CSDA_MD);
#endif
- pxa_set_cken(CKEN14_I2C, 1);
+ pxa_set_cken(CKEN_I2C, 1);
break;
#ifdef CONFIG_PXA27x
case 1:
local_irq_disable();
PCFR |= PCFR_PI2CEN;
local_irq_enable();
- pxa_set_cken(CKEN15_PWRI2C, 1);
+ pxa_set_cken(CKEN_PWRI2C, 1);
#endif
}
@@ -935,11 +935,11 @@
ereqirq:
switch (dev->id) {
case 0:
- pxa_set_cken(CKEN14_I2C, 0);
+ pxa_set_cken(CKEN_I2C, 0);
break;
#ifdef CONFIG_PXA27x
case 1:
- pxa_set_cken(CKEN15_PWRI2C, 0);
+ pxa_set_cken(CKEN_PWRI2C, 0);
local_irq_disable();
PCFR &= ~PCFR_PI2CEN;
local_irq_enable();
@@ -962,11 +962,11 @@
free_irq(i2c->irq, i2c);
switch (dev->id) {
case 0:
- pxa_set_cken(CKEN14_I2C, 0);
+ pxa_set_cken(CKEN_I2C, 0);
break;
#ifdef CONFIG_PXA27x
case 1:
- pxa_set_cken(CKEN15_PWRI2C, 0);
+ pxa_set_cken(CKEN_PWRI2C, 0);
local_irq_disable();
PCFR &= ~PCFR_PI2CEN;
local_irq_enable();
diff --git a/drivers/mmc/pxamci.c b/drivers/mmc/pxamci.c
index 9774fc6..fca894e5 100644
--- a/drivers/mmc/pxamci.c
+++ b/drivers/mmc/pxamci.c
@@ -369,14 +369,14 @@
if (CLOCKRATE / clk > ios->clock)
clk <<= 1;
host->clkrt = fls(clk) - 1;
- pxa_set_cken(CKEN12_MMC, 1);
+ pxa_set_cken(CKEN_MMC, 1);
/*
* we write clkrt on the next command
*/
} else {
pxamci_stop_clock(host);
- pxa_set_cken(CKEN12_MMC, 0);
+ pxa_set_cken(CKEN_MMC, 0);
}
if (host->power_mode != ios->power_mode) {
diff --git a/drivers/net/irda/pxaficp_ir.c b/drivers/net/irda/pxaficp_ir.c
index 2272156..d6d5361 100644
--- a/drivers/net/irda/pxaficp_ir.c
+++ b/drivers/net/irda/pxaficp_ir.c
@@ -134,7 +134,7 @@
DCSR(si->rxdma) &= ~DCSR_RUN;
/* disable FICP */
ICCR0 = 0;
- pxa_set_cken(CKEN13_FICP, 0);
+ pxa_set_cken(CKEN_FICP, 0);
/* set board transceiver to SIR mode */
si->pdata->transceiver_mode(si->dev, IR_SIRMODE);
@@ -144,7 +144,7 @@
pxa_gpio_mode(GPIO47_STTXD_MD);
/* enable the STUART clock */
- pxa_set_cken(CKEN5_STUART, 1);
+ pxa_set_cken(CKEN_STUART, 1);
}
/* disable STUART first */
@@ -169,7 +169,7 @@
/* disable STUART */
STIER = 0;
STISR = 0;
- pxa_set_cken(CKEN5_STUART, 0);
+ pxa_set_cken(CKEN_STUART, 0);
/* disable FICP first */
ICCR0 = 0;
@@ -182,7 +182,7 @@
pxa_gpio_mode(GPIO47_ICPTXD_MD);
/* enable the FICP clock */
- pxa_set_cken(CKEN13_FICP, 1);
+ pxa_set_cken(CKEN_FICP, 1);
si->speed = speed;
pxa_irda_fir_dma_rx_start(si);
@@ -593,7 +593,7 @@
/* disable STUART SIR mode */
STISR = 0;
/* disable the STUART clock */
- pxa_set_cken(CKEN5_STUART, 0);
+ pxa_set_cken(CKEN_STUART, 0);
/* disable DMA */
DCSR(si->txdma) &= ~DCSR_RUN;
@@ -601,7 +601,7 @@
/* disable FICP */
ICCR0 = 0;
/* disable the FICP clock */
- pxa_set_cken(CKEN13_FICP, 0);
+ pxa_set_cken(CKEN_FICP, 0);
DRCMR17 = 0;
DRCMR18 = 0;
diff --git a/drivers/serial/pxa.c b/drivers/serial/pxa.c
index d403aaa..e9c6cb3 100644
--- a/drivers/serial/pxa.c
+++ b/drivers/serial/pxa.c
@@ -717,7 +717,7 @@
static struct uart_pxa_port serial_pxa_ports[] = {
{ /* FFUART */
.name = "FFUART",
- .cken = CKEN6_FFUART,
+ .cken = CKEN_FFUART,
.port = {
.type = PORT_PXA,
.iotype = UPIO_MEM,
@@ -731,7 +731,7 @@
},
}, { /* BTUART */
.name = "BTUART",
- .cken = CKEN7_BTUART,
+ .cken = CKEN_BTUART,
.port = {
.type = PORT_PXA,
.iotype = UPIO_MEM,
@@ -745,7 +745,7 @@
},
}, { /* STUART */
.name = "STUART",
- .cken = CKEN5_STUART,
+ .cken = CKEN_STUART,
.port = {
.type = PORT_PXA,
.iotype = UPIO_MEM,
@@ -759,7 +759,7 @@
},
}, { /* HWUART */
.name = "HWUART",
- .cken = CKEN4_HWUART,
+ .cken = CKEN_HWUART,
.port = {
.type = PORT_PXA,
.iotype = UPIO_MEM,
diff --git a/drivers/usb/gadget/pxa2xx_udc.c b/drivers/usb/gadget/pxa2xx_udc.c
index f01890d..018b0d6 100644
--- a/drivers/usb/gadget/pxa2xx_udc.c
+++ b/drivers/usb/gadget/pxa2xx_udc.c
@@ -1497,7 +1497,7 @@
#ifdef CONFIG_ARCH_PXA
/* Disable clock for USB device */
- pxa_set_cken(CKEN11_USB, 0);
+ pxa_set_cken(CKEN_USB, 0);
#endif
ep0_idle (dev);
@@ -1543,7 +1543,7 @@
#ifdef CONFIG_ARCH_PXA
/* Enable clock for USB device */
- pxa_set_cken(CKEN11_USB, 1);
+ pxa_set_cken(CKEN_USB, 1);
udelay(5);
#endif
diff --git a/drivers/usb/host/ohci-pxa27x.c b/drivers/usb/host/ohci-pxa27x.c
index f1563dc..23d2fe5 100644
--- a/drivers/usb/host/ohci-pxa27x.c
+++ b/drivers/usb/host/ohci-pxa27x.c
@@ -80,7 +80,7 @@
inf = dev->platform_data;
- pxa_set_cken(CKEN10_USBHOST, 1);
+ pxa_set_cken(CKEN_USBHOST, 1);
UHCHR |= UHCHR_FHR;
udelay(11);
@@ -123,7 +123,7 @@
UHCCOMS |= 1;
udelay(10);
- pxa_set_cken(CKEN10_USBHOST, 0);
+ pxa_set_cken(CKEN_USBHOST, 0);
}
diff --git a/drivers/video/pxafb.c b/drivers/video/pxafb.c
index b4947c8..0b195f3 100644
--- a/drivers/video/pxafb.c
+++ b/drivers/video/pxafb.c
@@ -803,7 +803,7 @@
pr_debug("reg_lccr3 0x%08x\n", (unsigned int) fbi->reg_lccr3);
/* enable LCD controller clock */
- pxa_set_cken(CKEN16_LCD, 1);
+ pxa_set_cken(CKEN_LCD, 1);
/* Sequence from 11.7.10 */
LCCR3 = fbi->reg_lccr3;
@@ -840,7 +840,7 @@
remove_wait_queue(&fbi->ctrlr_wait, &wait);
/* disable LCD controller clock */
- pxa_set_cken(CKEN16_LCD, 0);
+ pxa_set_cken(CKEN_LCD, 0);
}
/*
diff --git a/include/asm-arm/arch-pxa/pxa-regs.h b/include/asm-arm/arch-pxa/pxa-regs.h
index 139c9d9..dbcc929 100644
--- a/include/asm-arm/arch-pxa/pxa-regs.h
+++ b/include/asm-arm/arch-pxa/pxa-regs.h
@@ -1801,35 +1801,35 @@
#define CCCR_M_MASK 0x0060 /* Memory Frequency to Run Mode Frequency Multiplier */
#define CCCR_L_MASK 0x001f /* Crystal Frequency to Memory Frequency Multiplier */
-#define CKEN24_CAMERA (1 << 24) /* Camera Interface Clock Enable */
-#define CKEN23_SSP1 (1 << 23) /* SSP1 Unit Clock Enable */
-#define CKEN22_MEMC (1 << 22) /* Memory Controller Clock Enable */
-#define CKEN21_MEMSTK (1 << 21) /* Memory Stick Host Controller */
-#define CKEN20_IM (1 << 20) /* Internal Memory Clock Enable */
-#define CKEN19_KEYPAD (1 << 19) /* Keypad Interface Clock Enable */
-#define CKEN18_USIM (1 << 18) /* USIM Unit Clock Enable */
-#define CKEN17_MSL (1 << 17) /* MSL Unit Clock Enable */
-#define CKEN16_LCD (1 << 16) /* LCD Unit Clock Enable */
-#define CKEN15_PWRI2C (1 << 15) /* PWR I2C Unit Clock Enable */
-#define CKEN14_I2C (1 << 14) /* I2C Unit Clock Enable */
-#define CKEN13_FICP (1 << 13) /* FICP Unit Clock Enable */
-#define CKEN12_MMC (1 << 12) /* MMC Unit Clock Enable */
-#define CKEN11_USB (1 << 11) /* USB Unit Clock Enable */
-#define CKEN10_ASSP (1 << 10) /* ASSP (SSP3) Clock Enable */
-#define CKEN10_USBHOST (1 << 10) /* USB Host Unit Clock Enable */
-#define CKEN9_OSTIMER (1 << 9) /* OS Timer Unit Clock Enable */
-#define CKEN9_NSSP (1 << 9) /* NSSP (SSP2) Clock Enable */
-#define CKEN8_I2S (1 << 8) /* I2S Unit Clock Enable */
-#define CKEN7_BTUART (1 << 7) /* BTUART Unit Clock Enable */
-#define CKEN6_FFUART (1 << 6) /* FFUART Unit Clock Enable */
-#define CKEN5_STUART (1 << 5) /* STUART Unit Clock Enable */
-#define CKEN4_HWUART (1 << 4) /* HWUART Unit Clock Enable */
-#define CKEN4_SSP3 (1 << 4) /* SSP3 Unit Clock Enable */
-#define CKEN3_SSP (1 << 3) /* SSP Unit Clock Enable */
-#define CKEN3_SSP2 (1 << 3) /* SSP2 Unit Clock Enable */
-#define CKEN2_AC97 (1 << 2) /* AC97 Unit Clock Enable */
-#define CKEN1_PWM1 (1 << 1) /* PWM1 Clock Enable */
-#define CKEN0_PWM0 (1 << 0) /* PWM0 Clock Enable */
+#define CKEN_CAMERA (24) /* Camera Interface Clock Enable */
+#define CKEN_SSP1 (23) /* SSP1 Unit Clock Enable */
+#define CKEN_MEMC (22) /* Memory Controller Clock Enable */
+#define CKEN_MEMSTK (21) /* Memory Stick Host Controller */
+#define CKEN_IM (20) /* Internal Memory Clock Enable */
+#define CKEN_KEYPAD (19) /* Keypad Interface Clock Enable */
+#define CKEN_USIM (18) /* USIM Unit Clock Enable */
+#define CKEN_MSL (17) /* MSL Unit Clock Enable */
+#define CKEN_LCD (16) /* LCD Unit Clock Enable */
+#define CKEN_PWRI2C (15) /* PWR I2C Unit Clock Enable */
+#define CKEN_I2C (14) /* I2C Unit Clock Enable */
+#define CKEN_FICP (13) /* FICP Unit Clock Enable */
+#define CKEN_MMC (12) /* MMC Unit Clock Enable */
+#define CKEN_USB (11) /* USB Unit Clock Enable */
+#define CKEN_ASSP (10) /* ASSP (SSP3) Clock Enable */
+#define CKEN_USBHOST (10) /* USB Host Unit Clock Enable */
+#define CKEN_OSTIMER (9) /* OS Timer Unit Clock Enable */
+#define CKEN_NSSP (9) /* NSSP (SSP2) Clock Enable */
+#define CKEN_I2S (8) /* I2S Unit Clock Enable */
+#define CKEN_BTUART (7) /* BTUART Unit Clock Enable */
+#define CKEN_FFUART (6) /* FFUART Unit Clock Enable */
+#define CKEN_STUART (5) /* STUART Unit Clock Enable */
+#define CKEN_HWUART (4) /* HWUART Unit Clock Enable */
+#define CKEN_SSP3 (4) /* SSP3 Unit Clock Enable */
+#define CKEN_SSP (3) /* SSP Unit Clock Enable */
+#define CKEN_SSP2 (3) /* SSP2 Unit Clock Enable */
+#define CKEN_AC97 (2) /* AC97 Unit Clock Enable */
+#define CKEN_PWM1 (1) /* PWM1 Clock Enable */
+#define CKEN_PWM0 (0) /* PWM0 Clock Enable */
#define OSCC_OON (1 << 1) /* 32.768kHz OON (write-once only bit) */
#define OSCC_OOK (1 << 0) /* 32.768kHz OOK (read-only bit) */
diff --git a/sound/arm/pxa2xx-ac97.c b/sound/arm/pxa2xx-ac97.c
index 28db4be..19c65a8 100644
--- a/sound/arm/pxa2xx-ac97.c
+++ b/sound/arm/pxa2xx-ac97.c
@@ -260,7 +260,7 @@
if (platform_ops && platform_ops->suspend)
platform_ops->suspend(platform_ops->priv);
GCR |= GCR_ACLINK_OFF;
- pxa_set_cken(CKEN2_AC97, 0);
+ pxa_set_cken(CKEN_AC97, 0);
return 0;
}
@@ -269,7 +269,7 @@
{
pxa2xx_audio_ops_t *platform_ops = card->dev->platform_data;
- pxa_set_cken(CKEN2_AC97, 1);
+ pxa_set_cken(CKEN_AC97, 1);
if (platform_ops && platform_ops->resume)
platform_ops->resume(platform_ops->priv);
snd_ac97_resume(pxa2xx_ac97_ac97);
@@ -337,7 +337,7 @@
/* Use GPIO 113 as AC97 Reset on Bulverde */
pxa_gpio_mode(113 | GPIO_ALT_FN_2_OUT);
#endif
- pxa_set_cken(CKEN2_AC97, 1);
+ pxa_set_cken(CKEN_AC97, 1);
ret = snd_ac97_bus(card, 0, &pxa2xx_ac97_ops, NULL, &ac97_bus);
if (ret)
@@ -361,10 +361,10 @@
err:
if (card)
snd_card_free(card);
- if (CKEN & CKEN2_AC97) {
+ if (CKEN & CKEN_AC97) {
GCR |= GCR_ACLINK_OFF;
free_irq(IRQ_AC97, NULL);
- pxa_set_cken(CKEN2_AC97, 0);
+ pxa_set_cken(CKEN_AC97, 0);
}
return ret;
}
@@ -378,7 +378,7 @@
platform_set_drvdata(dev, NULL);
GCR |= GCR_ACLINK_OFF;
free_irq(IRQ_AC97, NULL);
- pxa_set_cken(CKEN2_AC97, 0);
+ pxa_set_cken(CKEN_AC97, 0);
}
return 0;
diff --git a/sound/soc/pxa/pxa2xx-ac97.c b/sound/soc/pxa/pxa2xx-ac97.c
index 1bbbeff..b222755 100644
--- a/sound/soc/pxa/pxa2xx-ac97.c
+++ b/sound/soc/pxa/pxa2xx-ac97.c
@@ -256,7 +256,7 @@
struct snd_soc_cpu_dai *dai)
{
GCR |= GCR_ACLINK_OFF;
- pxa_set_cken(CKEN2_AC97, 0);
+ pxa_set_cken(CKEN_AC97, 0);
return 0;
}
@@ -271,7 +271,7 @@
/* Use GPIO 113 as AC97 Reset on Bulverde */
pxa_gpio_mode(113 | GPIO_ALT_FN_2_OUT);
#endif
- pxa_set_cken(CKEN2_AC97, 1);
+ pxa_set_cken(CKEN_AC97, 1);
return 0;
}
@@ -296,14 +296,14 @@
/* Use GPIO 113 as AC97 Reset on Bulverde */
pxa_gpio_mode(113 | GPIO_ALT_FN_2_OUT);
#endif
- pxa_set_cken(CKEN2_AC97, 1);
+ pxa_set_cken(CKEN_AC97, 1);
return 0;
err:
- if (CKEN & CKEN2_AC97) {
+ if (CKEN & CKEN_AC97) {
GCR |= GCR_ACLINK_OFF;
free_irq(IRQ_AC97, NULL);
- pxa_set_cken(CKEN2_AC97, 0);
+ pxa_set_cken(CKEN_AC97, 0);
}
return ret;
}
@@ -312,7 +312,7 @@
{
GCR |= GCR_ACLINK_OFF;
free_irq(IRQ_AC97, NULL);
- pxa_set_cken(CKEN2_AC97, 0);
+ pxa_set_cken(CKEN_AC97, 0);
}
static int pxa2xx_ac97_hw_params(struct snd_pcm_substream *substream,
diff --git a/sound/soc/pxa/pxa2xx-i2s.c b/sound/soc/pxa/pxa2xx-i2s.c
index 575a613..50c5c83 100644
--- a/sound/soc/pxa/pxa2xx-i2s.c
+++ b/sound/soc/pxa/pxa2xx-i2s.c
@@ -149,7 +149,7 @@
pxa_gpio_mode(gpio_bus[pxa_i2s.master].tx);
pxa_gpio_mode(gpio_bus[pxa_i2s.master].frm);
pxa_gpio_mode(gpio_bus[pxa_i2s.master].clk);
- pxa_set_cken(CKEN8_I2S, 1);
+ pxa_set_cken(CKEN_I2S, 1);
pxa_i2s_wait();
if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK)
@@ -234,7 +234,7 @@
if (SACR1 & (SACR1_DREC | SACR1_DRPL)) {
SACR0 &= ~SACR0_ENB;
pxa_i2s_wait();
- pxa_set_cken(CKEN8_I2S, 0);
+ pxa_set_cken(CKEN_I2S, 0);
}
}
