| # |
| # Makefile for the Linux kernel device drivers. |
| # |
| # 15 Sep 2000, Christoph Hellwig <hch@infradead.org> |
| # Rewritten to use lists instead of if-statements. |
| # |
| |
| obj-y += gpio/ |
| obj-$(CONFIG_PCI) += pci/ |
| obj-$(CONFIG_PARISC) += parisc/ |
| obj-$(CONFIG_RAPIDIO) += rapidio/ |
| obj-y += video/ |
| obj-$(CONFIG_ACPI) += acpi/ |
| # PnP must come after ACPI since it will eventually need to check if acpi |
| # was used and do nothing if so |
| obj-$(CONFIG_PNP) += pnp/ |
| obj-$(CONFIG_ARM_AMBA) += amba/ |
| |
| obj-$(CONFIG_XEN) += xen/ |
| |
| # char/ comes before serial/ etc so that the VT console is the boot-time |
| # default. |
| obj-y += char/ |
| |
| # gpu/ comes after char for AGP vs DRM startup |
| obj-y += gpu/ |
| |
| obj-$(CONFIG_CONNECTOR) += connector/ |
| |
| # i810fb and intelfb depend on char/agp/ |
| obj-$(CONFIG_FB_I810) += video/i810/ |
| obj-$(CONFIG_FB_INTEL) += video/intelfb/ |
| |
| obj-y += serial/ |
| obj-$(CONFIG_PARPORT) += parport/ |
| obj-y += base/ block/ misc/ mfd/ net/ media/ |
| obj-$(CONFIG_NUBUS) += nubus/ |
| obj-$(CONFIG_ATM) += atm/ |
| obj-y += macintosh/ |
| obj-$(CONFIG_IDE) += ide/ |
| obj-$(CONFIG_SCSI) += scsi/ |
| obj-$(CONFIG_ATA) += ata/ |
| obj-$(CONFIG_FUSION) += message/ |
| obj-$(CONFIG_FIREWIRE) += firewire/ |
| obj-y += ieee1394/ |
| obj-$(CONFIG_UIO) += uio/ |
| obj-y += cdrom/ |
| obj-y += auxdisplay/ |
| obj-$(CONFIG_MTD) += mtd/ |
| obj-$(CONFIG_SPI) += spi/ |
| obj-$(CONFIG_PCCARD) += pcmcia/ |
| obj-$(CONFIG_DIO) += dio/ |
| obj-$(CONFIG_SBUS) += sbus/ |
| obj-$(CONFIG_ZORRO) += zorro/ |
| obj-$(CONFIG_MAC) += macintosh/ |
| obj-$(CONFIG_ATA_OVER_ETH) += block/aoe/ |
| obj-$(CONFIG_PARIDE) += block/paride/ |
| obj-$(CONFIG_TC) += tc/ |
| obj-$(CONFIG_USB) += usb/ |
| obj-$(CONFIG_USB_MUSB_HDRC) += usb/musb/ |
| obj-$(CONFIG_PCI) += usb/ |
| obj-$(CONFIG_USB_GADGET) += usb/gadget/ |
| obj-$(CONFIG_SERIO) += input/serio/ |
| obj-$(CONFIG_GAMEPORT) += input/gameport/ |
| obj-$(CONFIG_INPUT) += input/ |
| obj-$(CONFIG_I2O) += message/ |
| obj-$(CONFIG_RTC_LIB) += rtc/ |
| obj-y += i2c/ |
| obj-$(CONFIG_W1) += w1/ |
| obj-$(CONFIG_POWER_SUPPLY) += power/ |
| obj-$(CONFIG_HWMON) += hwmon/ |
| obj-$(CONFIG_THERMAL) += thermal/ |
| obj-$(CONFIG_WATCHDOG) += watchdog/ |
| obj-$(CONFIG_PHONE) += telephony/ |
| obj-$(CONFIG_MD) += md/ |
| obj-$(CONFIG_BT) += bluetooth/ |
| obj-$(CONFIG_ACCESSIBILITY) += accessibility/ |
| obj-$(CONFIG_ISDN) += isdn/ |
| obj-$(CONFIG_EDAC) += edac/ |
| obj-$(CONFIG_MCA) += mca/ |
| obj-$(CONFIG_EISA) += eisa/ |
| obj-y += lguest/ |
| obj-$(CONFIG_CPU_FREQ) += cpufreq/ |
| obj-$(CONFIG_CPU_IDLE) += cpuidle/ |
| obj-$(CONFIG_MMC) += mmc/ |
| obj-$(CONFIG_MEMSTICK) += memstick/ |
| obj-$(CONFIG_NEW_LEDS) += leds/ |
| obj-$(CONFIG_INFINIBAND) += infiniband/ |
| obj-$(CONFIG_SGI_SN) += sn/ |
| obj-y += firmware/ |
| obj-$(CONFIG_CRYPTO) += crypto/ |
| obj-$(CONFIG_SUPERH) += sh/ |
| obj-$(CONFIG_GENERIC_TIME) += clocksource/ |
| obj-$(CONFIG_DMA_ENGINE) += dma/ |
| obj-$(CONFIG_DCA) += dca/ |
| obj-$(CONFIG_HID) += hid/ |
| obj-$(CONFIG_PPC_PS3) += ps3/ |
| obj-$(CONFIG_OF) += of/ |
| obj-$(CONFIG_SSB) += ssb/ |
| obj-$(CONFIG_VIRTIO) += virtio/ |
| obj-$(CONFIG_REGULATOR) += regulator/ |
| obj-$(CONFIG_UWB) += uwb/ |
