| /* |
| * linux/arch/arm/mach-pxa/saar.c |
| * |
| * Support for the Marvell PXA930 Handheld Platform (aka SAAR) |
| * |
| * Copyright (C) 2007-2008 Marvell International Ltd. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * publishhed by the Free Software Foundation. |
| */ |
| |
| #include <linux/module.h> |
| #include <linux/kernel.h> |
| #include <linux/interrupt.h> |
| #include <linux/init.h> |
| #include <linux/platform_device.h> |
| #include <linux/clk.h> |
| #include <linux/gpio.h> |
| #include <linux/delay.h> |
| #include <linux/fb.h> |
| #include <linux/i2c.h> |
| #include <linux/i2c/pxa-i2c.h> |
| #include <linux/smc91x.h> |
| #include <linux/mfd/da903x.h> |
| #include <linux/mtd/mtd.h> |
| #include <linux/mtd/partitions.h> |
| #include <linux/mtd/onenand.h> |
| |
| #include <asm/mach-types.h> |
| #include <asm/mach/arch.h> |
| #include <asm/mach/flash.h> |
| |
| #include <mach/pxa930.h> |
| #include <mach/pxafb.h> |
| |
| #include "devices.h" |
| #include "generic.h" |
| |
| #define GPIO_LCD_RESET (16) |
| |
| /* SAAR MFP configurations */ |
| static mfp_cfg_t saar_mfp_cfg[] __initdata = { |
| /* LCD */ |
| GPIO23_LCD_DD0, |
| GPIO24_LCD_DD1, |
| GPIO25_LCD_DD2, |
| GPIO26_LCD_DD3, |
| GPIO27_LCD_DD4, |
| GPIO28_LCD_DD5, |
| GPIO29_LCD_DD6, |
| GPIO44_LCD_DD7, |
| GPIO21_LCD_CS, |
| GPIO22_LCD_VSYNC, |
| GPIO17_LCD_FCLK_RD, |
| GPIO18_LCD_LCLK_A0, |
| GPIO19_LCD_PCLK_WR, |
| GPIO16_GPIO, /* LCD reset */ |
| |
| /* Ethernet */ |
| DF_nCS1_nCS3, |
| GPIO97_GPIO, |
| |
| /* DFI */ |
| DF_INT_RnB_ND_INT_RnB, |
| DF_nRE_nOE_ND_nRE, |
| DF_nWE_ND_nWE, |
| DF_CLE_nOE_ND_CLE, |
| DF_nADV1_ALE_ND_ALE, |
| DF_nADV2_ALE_nCS3, |
| DF_nCS0_ND_nCS0, |
| DF_IO0_ND_IO0, |
| DF_IO1_ND_IO1, |
| DF_IO2_ND_IO2, |
| DF_IO3_ND_IO3, |
| DF_IO4_ND_IO4, |
| DF_IO5_ND_IO5, |
| DF_IO6_ND_IO6, |
| DF_IO7_ND_IO7, |
| DF_IO8_ND_IO8, |
| DF_IO9_ND_IO9, |
| DF_IO10_ND_IO10, |
| DF_IO11_ND_IO11, |
| DF_IO12_ND_IO12, |
| DF_IO13_ND_IO13, |
| DF_IO14_ND_IO14, |
| DF_IO15_ND_IO15, |
| }; |
| |
| #define SAAR_ETH_PHYS (0x14000000) |
| |
| static struct resource smc91x_resources[] = { |
| [0] = { |
| .start = (SAAR_ETH_PHYS + 0x300), |
| .end = (SAAR_ETH_PHYS + 0xfffff), |
| .flags = IORESOURCE_MEM, |
| }, |
| [1] = { |
| .start = gpio_to_irq(mfp_to_gpio(MFP_PIN_GPIO97)), |
| .end = gpio_to_irq(mfp_to_gpio(MFP_PIN_GPIO97)), |
| .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE, |
| } |
| }; |
| |
| static struct smc91x_platdata saar_smc91x_info = { |
| .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT | SMC91X_USE_DMA, |
| }; |
| |
| static struct platform_device smc91x_device = { |
| .name = "smc91x", |
| .id = 0, |
| .num_resources = ARRAY_SIZE(smc91x_resources), |
| .resource = smc91x_resources, |
| .dev = { |
| .platform_data = &saar_smc91x_info, |
| }, |
| }; |
| |
| #if defined(CONFIG_FB_PXA) || defined(CONFIG_FB_PXA_MODULE) |
| static uint16_t lcd_power_on[] = { |
| /* single frame */ |
| SMART_CMD_NOOP, |
| SMART_CMD(0x00), |
| SMART_DELAY(0), |
| |
| SMART_CMD_NOOP, |
| SMART_CMD(0x00), |
| SMART_DELAY(0), |
| |
| SMART_CMD_NOOP, |
| SMART_CMD(0x00), |
| SMART_DELAY(0), |
| |
| SMART_CMD_NOOP, |
| SMART_CMD(0x00), |
| SMART_DELAY(10), |
| |
| /* calibration control */ |
| SMART_CMD(0x00), |
| SMART_CMD(0xA4), |
| SMART_DAT(0x80), |
| SMART_DAT(0x01), |
| SMART_DELAY(150), |
| |
| /*Power-On Init sequence*/ |
| SMART_CMD(0x00), /* output ctrl */ |
| SMART_CMD(0x01), |
| SMART_DAT(0x01), |
| SMART_DAT(0x00), |
| SMART_CMD(0x00), /* wave ctrl */ |
| SMART_CMD(0x02), |
| SMART_DAT(0x07), |
| SMART_DAT(0x00), |
| SMART_CMD(0x00), |
| SMART_CMD(0x03), /* entry mode */ |
| SMART_DAT(0xD0), |
| SMART_DAT(0x30), |
| SMART_CMD(0x00), |
| SMART_CMD(0x08), /* display ctrl 2 */ |
| SMART_DAT(0x08), |
| SMART_DAT(0x08), |
| SMART_CMD(0x00), |
| SMART_CMD(0x09), /* display ctrl 3 */ |
| SMART_DAT(0x04), |
| SMART_DAT(0x2F), |
| SMART_CMD(0x00), |
| SMART_CMD(0x0A), /* display ctrl 4 */ |
| SMART_DAT(0x00), |
| SMART_DAT(0x08), |
| SMART_CMD(0x00), |
| SMART_CMD(0x0D), /* Frame Marker position */ |
| SMART_DAT(0x00), |
| SMART_DAT(0x08), |
| SMART_CMD(0x00), |
| SMART_CMD(0x60), /* Driver output control */ |
| SMART_DAT(0x27), |
| SMART_DAT(0x00), |
| SMART_CMD(0x00), |
| SMART_CMD(0x61), /* Base image display control */ |
| SMART_DAT(0x00), |
| SMART_DAT(0x01), |
| SMART_CMD(0x00), |
| SMART_CMD(0x30), /* Y settings 30h-3Dh */ |
| SMART_DAT(0x07), |
| SMART_DAT(0x07), |
| SMART_CMD(0x00), |
| SMART_CMD(0x31), |
| SMART_DAT(0x00), |
| SMART_DAT(0x07), |
| SMART_CMD(0x00), |
| SMART_CMD(0x32), /* Timing(3), ASW HOLD=0.5CLK */ |
| SMART_DAT(0x04), |
| SMART_DAT(0x00), |
| SMART_CMD(0x00), |
| SMART_CMD(0x33), /* Timing(4), CKV ST=0CLK, CKV ED=1CLK */ |
| SMART_DAT(0x03), |
| SMART_DAT(0x03), |
| SMART_CMD(0x00), |
| SMART_CMD(0x34), |
| SMART_DAT(0x00), |
| SMART_DAT(0x00), |
| SMART_CMD(0x00), |
| SMART_CMD(0x35), |
| SMART_DAT(0x02), |
| SMART_DAT(0x05), |
| SMART_CMD(0x00), |
| SMART_CMD(0x36), |
| SMART_DAT(0x1F), |
| SMART_DAT(0x1F), |
| SMART_CMD(0x00), |
| SMART_CMD(0x37), |
| SMART_DAT(0x07), |
| SMART_DAT(0x07), |
| SMART_CMD(0x00), |
| SMART_CMD(0x38), |
| SMART_DAT(0x00), |
| SMART_DAT(0x07), |
| SMART_CMD(0x00), |
| SMART_CMD(0x39), |
| SMART_DAT(0x04), |
| SMART_DAT(0x00), |
| SMART_CMD(0x00), |
| SMART_CMD(0x3A), |
| SMART_DAT(0x03), |
| SMART_DAT(0x03), |
| SMART_CMD(0x00), |
| SMART_CMD(0x3B), |
| SMART_DAT(0x00), |
| SMART_DAT(0x00), |
| SMART_CMD(0x00), |
| SMART_CMD(0x3C), |
| SMART_DAT(0x02), |
| SMART_DAT(0x05), |
| SMART_CMD(0x00), |
| SMART_CMD(0x3D), |
| SMART_DAT(0x1F), |
| SMART_DAT(0x1F), |
| SMART_CMD(0x00), /* Display control 1 */ |
| SMART_CMD(0x07), |
| SMART_DAT(0x00), |
| SMART_DAT(0x01), |
| SMART_CMD(0x00), /* Power control 5 */ |
| SMART_CMD(0x17), |
| SMART_DAT(0x00), |
| SMART_DAT(0x01), |
| SMART_CMD(0x00), /* Power control 1 */ |
| SMART_CMD(0x10), |
| SMART_DAT(0x10), |
| SMART_DAT(0xB0), |
| SMART_CMD(0x00), /* Power control 2 */ |
| SMART_CMD(0x11), |
| SMART_DAT(0x01), |
| SMART_DAT(0x30), |
| SMART_CMD(0x00), /* Power control 3 */ |
| SMART_CMD(0x12), |
| SMART_DAT(0x01), |
| SMART_DAT(0x9E), |
| SMART_CMD(0x00), /* Power control 4 */ |
| SMART_CMD(0x13), |
| SMART_DAT(0x17), |
| SMART_DAT(0x00), |
| SMART_CMD(0x00), /* Power control 3 */ |
| SMART_CMD(0x12), |
| SMART_DAT(0x01), |
| SMART_DAT(0xBE), |
| SMART_DELAY(100), |
| |
| /* display mode : 240*320 */ |
| SMART_CMD(0x00), /* RAM address set(H) 0*/ |
| SMART_CMD(0x20), |
| SMART_DAT(0x00), |
| SMART_DAT(0x00), |
| SMART_CMD(0x00), /* RAM address set(V) 4*/ |
| SMART_CMD(0x21), |
| SMART_DAT(0x00), |
| SMART_DAT(0x00), |
| SMART_CMD(0x00), /* Start of Window RAM address set(H) 8*/ |
| SMART_CMD(0x50), |
| SMART_DAT(0x00), |
| SMART_DAT(0x00), |
| SMART_CMD(0x00), /* End of Window RAM address set(H) 12*/ |
| SMART_CMD(0x51), |
| SMART_DAT(0x00), |
| SMART_DAT(0xEF), |
| SMART_CMD(0x00), /* Start of Window RAM address set(V) 16*/ |
| SMART_CMD(0x52), |
| SMART_DAT(0x00), |
| SMART_DAT(0x00), |
| SMART_CMD(0x00), /* End of Window RAM address set(V) 20*/ |
| SMART_CMD(0x53), |
| SMART_DAT(0x01), |
| SMART_DAT(0x3F), |
| SMART_CMD(0x00), /* Panel interface control 1 */ |
| SMART_CMD(0x90), |
| SMART_DAT(0x00), |
| SMART_DAT(0x1A), |
| SMART_CMD(0x00), /* Panel interface control 2 */ |
| SMART_CMD(0x92), |
| SMART_DAT(0x04), |
| SMART_DAT(0x00), |
| SMART_CMD(0x00), /* Panel interface control 3 */ |
| SMART_CMD(0x93), |
| SMART_DAT(0x00), |
| SMART_DAT(0x05), |
| SMART_DELAY(20), |
| }; |
| |
| static uint16_t lcd_panel_on[] = { |
| SMART_CMD(0x00), |
| SMART_CMD(0x07), |
| SMART_DAT(0x00), |
| SMART_DAT(0x21), |
| SMART_DELAY(1), |
| |
| SMART_CMD(0x00), |
| SMART_CMD(0x07), |
| SMART_DAT(0x00), |
| SMART_DAT(0x61), |
| SMART_DELAY(100), |
| |
| SMART_CMD(0x00), |
| SMART_CMD(0x07), |
| SMART_DAT(0x01), |
| SMART_DAT(0x73), |
| SMART_DELAY(1), |
| }; |
| |
| static uint16_t lcd_panel_off[] = { |
| SMART_CMD(0x00), |
| SMART_CMD(0x07), |
| SMART_DAT(0x00), |
| SMART_DAT(0x72), |
| SMART_DELAY(40), |
| |
| SMART_CMD(0x00), |
| SMART_CMD(0x07), |
| SMART_DAT(0x00), |
| SMART_DAT(0x01), |
| SMART_DELAY(1), |
| |
| SMART_CMD(0x00), |
| SMART_CMD(0x07), |
| SMART_DAT(0x00), |
| SMART_DAT(0x00), |
| SMART_DELAY(1), |
| }; |
| |
| static uint16_t lcd_power_off[] = { |
| SMART_CMD(0x00), |
| SMART_CMD(0x10), |
| SMART_DAT(0x00), |
| SMART_DAT(0x80), |
| |
| SMART_CMD(0x00), |
| SMART_CMD(0x11), |
| SMART_DAT(0x01), |
| SMART_DAT(0x60), |
| |
| SMART_CMD(0x00), |
| SMART_CMD(0x12), |
| SMART_DAT(0x01), |
| SMART_DAT(0xAE), |
| SMART_DELAY(40), |
| |
| SMART_CMD(0x00), |
| SMART_CMD(0x10), |
| SMART_DAT(0x00), |
| SMART_DAT(0x00), |
| }; |
| |
| static uint16_t update_framedata[] = { |
| /* set display ram: 240*320 */ |
| SMART_CMD(0x00), /* RAM address set(H) 0*/ |
| SMART_CMD(0x20), |
| SMART_DAT(0x00), |
| SMART_DAT(0x00), |
| SMART_CMD(0x00), /* RAM address set(V) 4*/ |
| SMART_CMD(0x21), |
| SMART_DAT(0x00), |
| SMART_DAT(0x00), |
| SMART_CMD(0x00), /* Start of Window RAM address set(H) 8 */ |
| SMART_CMD(0x50), |
| SMART_DAT(0x00), |
| SMART_DAT(0x00), |
| SMART_CMD(0x00), /* End of Window RAM address set(H) 12 */ |
| SMART_CMD(0x51), |
| SMART_DAT(0x00), |
| SMART_DAT(0xEF), |
| SMART_CMD(0x00), /* Start of Window RAM address set(V) 16 */ |
| SMART_CMD(0x52), |
| SMART_DAT(0x00), |
| SMART_DAT(0x00), |
| SMART_CMD(0x00), /* End of Window RAM address set(V) 20 */ |
| SMART_CMD(0x53), |
| SMART_DAT(0x01), |
| SMART_DAT(0x3F), |
| |
| /* wait for vsync cmd before transferring frame data */ |
| SMART_CMD_WAIT_FOR_VSYNC, |
| |
| /* write ram */ |
| SMART_CMD(0x00), |
| SMART_CMD(0x22), |
| |
| /* write frame data */ |
| SMART_CMD_WRITE_FRAME, |
| }; |
| |
| static void ltm022a97a_lcd_power(int on, struct fb_var_screeninfo *var) |
| { |
| static int pin_requested = 0; |
| struct fb_info *info = container_of(var, struct fb_info, var); |
| int err; |
| |
| if (!pin_requested) { |
| err = gpio_request(GPIO_LCD_RESET, "lcd reset"); |
| if (err) { |
| pr_err("failed to request gpio for LCD reset\n"); |
| return; |
| } |
| |
| gpio_direction_output(GPIO_LCD_RESET, 0); |
| pin_requested = 1; |
| } |
| |
| if (on) { |
| gpio_set_value(GPIO_LCD_RESET, 0); msleep(100); |
| gpio_set_value(GPIO_LCD_RESET, 1); msleep(10); |
| |
| pxafb_smart_queue(info, ARRAY_AND_SIZE(lcd_power_on)); |
| pxafb_smart_queue(info, ARRAY_AND_SIZE(lcd_panel_on)); |
| } else { |
| pxafb_smart_queue(info, ARRAY_AND_SIZE(lcd_panel_off)); |
| pxafb_smart_queue(info, ARRAY_AND_SIZE(lcd_power_off)); |
| } |
| |
| err = pxafb_smart_flush(info); |
| if (err) |
| pr_err("%s: timed out\n", __func__); |
| } |
| |
| static void ltm022a97a_update(struct fb_info *info) |
| { |
| pxafb_smart_queue(info, ARRAY_AND_SIZE(update_framedata)); |
| pxafb_smart_flush(info); |
| } |
| |
| static struct pxafb_mode_info toshiba_ltm022a97a_modes[] = { |
| [0] = { |
| .xres = 240, |
| .yres = 320, |
| .bpp = 16, |
| .a0csrd_set_hld = 30, |
| .a0cswr_set_hld = 30, |
| .wr_pulse_width = 30, |
| .rd_pulse_width = 30, |
| .op_hold_time = 30, |
| .cmd_inh_time = 60, |
| |
| /* L_LCLK_A0 and L_LCLK_RD active low */ |
| .sync = FB_SYNC_HOR_HIGH_ACT | |
| FB_SYNC_VERT_HIGH_ACT, |
| }, |
| }; |
| |
| static struct pxafb_mach_info saar_lcd_info = { |
| .modes = toshiba_ltm022a97a_modes, |
| .num_modes = 1, |
| .lcd_conn = LCD_SMART_PANEL_8BPP | LCD_PCLK_EDGE_FALL, |
| .pxafb_lcd_power = ltm022a97a_lcd_power, |
| .smart_update = ltm022a97a_update, |
| }; |
| |
| static void __init saar_init_lcd(void) |
| { |
| pxa_set_fb_info(NULL, &saar_lcd_info); |
| } |
| #else |
| static inline void saar_init_lcd(void) {} |
| #endif |
| |
| #if defined(CONFIG_I2C_PXA) || defined(CONFIG_I2C_PXA_MODULE) |
| static struct da9034_backlight_pdata saar_da9034_backlight = { |
| .output_current = 4, /* 4mA */ |
| }; |
| |
| static struct da903x_subdev_info saar_da9034_subdevs[] = { |
| [0] = { |
| .name = "da903x-backlight", |
| .id = DA9034_ID_WLED, |
| .platform_data = &saar_da9034_backlight, |
| }, |
| }; |
| |
| static struct da903x_platform_data saar_da9034_info = { |
| .num_subdevs = ARRAY_SIZE(saar_da9034_subdevs), |
| .subdevs = saar_da9034_subdevs, |
| }; |
| |
| static struct i2c_board_info saar_i2c_info[] = { |
| [0] = { |
| .type = "da9034", |
| .addr = 0x34, |
| .platform_data = &saar_da9034_info, |
| .irq = gpio_to_irq(mfp_to_gpio(MFP_PIN_GPIO83)), |
| }, |
| }; |
| |
| static void __init saar_init_i2c(void) |
| { |
| pxa_set_i2c_info(NULL); |
| i2c_register_board_info(0, ARRAY_AND_SIZE(saar_i2c_info)); |
| } |
| #else |
| static inline void saar_init_i2c(void) {} |
| #endif |
| |
| #if defined(CONFIG_MTD_ONENAND) || defined(CONFIG_MTD_ONENAND_MODULE) |
| static struct mtd_partition saar_onenand_partitions[] = { |
| { |
| .name = "bootloader", |
| .offset = 0, |
| .size = SZ_1M, |
| .mask_flags = MTD_WRITEABLE, |
| }, { |
| .name = "reserved", |
| .offset = MTDPART_OFS_APPEND, |
| .size = SZ_128K, |
| .mask_flags = MTD_WRITEABLE, |
| }, { |
| .name = "reserved", |
| .offset = MTDPART_OFS_APPEND, |
| .size = SZ_8M, |
| .mask_flags = MTD_WRITEABLE, |
| }, { |
| .name = "kernel", |
| .offset = MTDPART_OFS_APPEND, |
| .size = (SZ_2M + SZ_1M), |
| .mask_flags = 0, |
| }, { |
| .name = "filesystem", |
| .offset = MTDPART_OFS_APPEND, |
| .size = SZ_48M, |
| .mask_flags = 0, |
| } |
| }; |
| |
| static struct onenand_platform_data saar_onenand_info = { |
| .parts = saar_onenand_partitions, |
| .nr_parts = ARRAY_SIZE(saar_onenand_partitions), |
| }; |
| |
| #define SMC_CS0_PHYS_BASE (0x10000000) |
| |
| static struct resource saar_resource_onenand[] = { |
| [0] = { |
| .start = SMC_CS0_PHYS_BASE, |
| .end = SMC_CS0_PHYS_BASE + SZ_1M, |
| .flags = IORESOURCE_MEM, |
| }, |
| }; |
| |
| static struct platform_device saar_device_onenand = { |
| .name = "onenand-flash", |
| .id = -1, |
| .dev = { |
| .platform_data = &saar_onenand_info, |
| }, |
| .resource = saar_resource_onenand, |
| .num_resources = ARRAY_SIZE(saar_resource_onenand), |
| }; |
| |
| static void __init saar_init_onenand(void) |
| { |
| platform_device_register(&saar_device_onenand); |
| } |
| #else |
| static void __init saar_init_onenand(void) {} |
| #endif |
| |
| static void __init saar_init(void) |
| { |
| /* initialize MFP configurations */ |
| pxa3xx_mfp_config(ARRAY_AND_SIZE(saar_mfp_cfg)); |
| |
| pxa_set_ffuart_info(NULL); |
| pxa_set_btuart_info(NULL); |
| pxa_set_stuart_info(NULL); |
| |
| platform_device_register(&smc91x_device); |
| saar_init_onenand(); |
| |
| saar_init_i2c(); |
| saar_init_lcd(); |
| } |
| |
| MACHINE_START(SAAR, "PXA930 Handheld Platform (aka SAAR)") |
| /* Maintainer: Eric Miao <eric.miao@marvell.com> */ |
| .boot_params = 0xa0000100, |
| .map_io = pxa3xx_map_io, |
| .init_irq = pxa3xx_init_irq, |
| .handle_irq = pxa3xx_handle_irq, |
| .timer = &pxa_timer, |
| .init_machine = saar_init, |
| MACHINE_END |
