arch/arm/mach-ixp4xx/dsmg600-setup.c - kernel/panda - Git at Google

 /*
  * DSM-G600 board-setup
  *
  * Copyright (C) 2008 Rod Whitby <rod@whitby.id.au>
  * Copyright (C) 2006 Tower Technologies
  *
  * based on ixdp425-setup.c:
  *      Copyright (C) 2003-2004 MontaVista Software, Inc.
  * based on nslu2-power.c:
  *	Copyright (C) 2005 Tower Technologies
  * based on nslu2-io.c:
  *	Copyright (C) 2004 Karen Spearel
  *
  * Author: Alessandro Zummo <a.zummo@towertech.it>
  * Author: Michael Westerhof <mwester@dls.net>
  * Author: Rod Whitby <rod@whitby.id.au>
  * Maintainers: http://www.nslu2-linux.org/
  */

 #include <linux/irq.h>
 #include <linux/jiffies.h>
 #include <linux/timer.h>
 #include <linux/serial.h>
 #include <linux/serial_8250.h>
 #include <linux/leds.h>
 #include <linux/reboot.h>
 #include <linux/i2c.h>
 #include <linux/i2c-gpio.h>

 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/flash.h>
 #include <asm/mach/time.h>
 #include <asm/gpio.h>

 #define DSMG600_SDA_PIN		5
 #define DSMG600_SCL_PIN		4

 /* DSM-G600 Timer Setting */
 #define DSMG600_FREQ		66000000

 /* Buttons */
 #define DSMG600_PB_GPIO		15	/* power button */
 #define DSMG600_RB_GPIO		3	/* reset button */

 /* Power control */
 #define DSMG600_PO_GPIO		2	/* power off */

 /* LEDs */
 #define DSMG600_LED_PWR_GPIO	0
 #define DSMG600_LED_WLAN_GPIO	14

 static struct flash_platform_data dsmg600_flash_data = {
 	.map_name		= "cfi_probe",
 	.width			= 2,
 };

 static struct resource dsmg600_flash_resource = {
 	.flags			= IORESOURCE_MEM,
 };

 static struct platform_device dsmg600_flash = {
 	.name			= "IXP4XX-Flash",
 	.id			= 0,
 	.dev.platform_data	= &dsmg600_flash_data,
 	.num_resources		= 1,
 	.resource		= &dsmg600_flash_resource,
 };

 static struct i2c_gpio_platform_data dsmg600_i2c_gpio_data = {
 	.sda_pin		= DSMG600_SDA_PIN,
 	.scl_pin		= DSMG600_SCL_PIN,
 };

 static struct platform_device dsmg600_i2c_gpio = {
 	.name			= "i2c-gpio",
 	.id			= 0,
 	.dev	 = {
 		.platform_data	= &dsmg600_i2c_gpio_data,
 	},
 };

 static struct i2c_board_info __initdata dsmg600_i2c_board_info [] = {
 	{
 		I2C_BOARD_INFO("pcf8563", 0x51),
 	},
 };

 static struct gpio_led dsmg600_led_pins[] = {
 	{
 		.name		= "dsmg600:green:power",
 		.gpio		= DSMG600_LED_PWR_GPIO,
 	},
 	{
 		.name		= "dsmg600:green:wlan",
 		.gpio		= DSMG600_LED_WLAN_GPIO,
 		.active_low	= true,
 	},
 };

 static struct gpio_led_platform_data dsmg600_led_data = {
 	.num_leds		= ARRAY_SIZE(dsmg600_led_pins),
 	.leds			= dsmg600_led_pins,
 };

 static struct platform_device dsmg600_leds = {
 	.name			= "leds-gpio",
 	.id			= -1,
 	.dev.platform_data	= &dsmg600_led_data,
 };

 static struct resource dsmg600_uart_resources[] = {
 	{
 		.start		= IXP4XX_UART1_BASE_PHYS,
 		.end		= IXP4XX_UART1_BASE_PHYS + 0x0fff,
 		.flags		= IORESOURCE_MEM,
 	},
 	{
 		.start		= IXP4XX_UART2_BASE_PHYS,
 		.end		= IXP4XX_UART2_BASE_PHYS + 0x0fff,
 		.flags		= IORESOURCE_MEM,
 	}
 };

 static struct plat_serial8250_port dsmg600_uart_data[] = {
 	{
 		.mapbase	= IXP4XX_UART1_BASE_PHYS,
 		.membase	= (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
 		.irq		= IRQ_IXP4XX_UART1,
 		.flags		= UPF_BOOT_AUTOCONF,
 		.iotype		= UPIO_MEM,
 		.regshift	= 2,
 		.uartclk	= IXP4XX_UART_XTAL,
 	},
 	{
 		.mapbase	= IXP4XX_UART2_BASE_PHYS,
 		.membase	= (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
 		.irq		= IRQ_IXP4XX_UART2,
 		.flags		= UPF_BOOT_AUTOCONF,
 		.iotype		= UPIO_MEM,
 		.regshift	= 2,
 		.uartclk	= IXP4XX_UART_XTAL,
 	},
 	{ }
 };

 static struct platform_device dsmg600_uart = {
 	.name			= "serial8250",
 	.id			= PLAT8250_DEV_PLATFORM,
 	.dev.platform_data	= dsmg600_uart_data,
 	.num_resources		= ARRAY_SIZE(dsmg600_uart_resources),
 	.resource		= dsmg600_uart_resources,
 };

 static struct platform_device *dsmg600_devices[] __initdata = {
 	&dsmg600_i2c_gpio,
 	&dsmg600_flash,
 	&dsmg600_leds,
 };

 static void dsmg600_power_off(void)
 {
 	/* enable the pwr cntl gpio */
 	gpio_line_config(DSMG600_PO_GPIO, IXP4XX_GPIO_OUT);

 	/* poweroff */
 	gpio_line_set(DSMG600_PO_GPIO, IXP4XX_GPIO_HIGH);
 }

 /* This is used to make sure the power-button pusher is serious.  The button
  * must be held until the value of this counter reaches zero.
  */
 static int power_button_countdown;

 /* Must hold the button down for at least this many counts to be processed */
 #define PBUTTON_HOLDDOWN_COUNT 4 /* 2 secs */

 static void dsmg600_power_handler(unsigned long data);
 static DEFINE_TIMER(dsmg600_power_timer, dsmg600_power_handler, 0, 0);

 static void dsmg600_power_handler(unsigned long data)
 {
 	/* This routine is called twice per second to check the
 	 * state of the power button.
 	 */

 	if (gpio_get_value(DSMG600_PB_GPIO)) {

 		/* IO Pin is 1 (button pushed) */
 		if (power_button_countdown > 0)
 			power_button_countdown--;

 	} else {

 		/* Done on button release, to allow for auto-power-on mods. */
 		if (power_button_countdown == 0) {
 			/* Signal init to do the ctrlaltdel action,
 			 * this will bypass init if it hasn't started
 			 * and do a kernel_restart.
 			 */
 			ctrl_alt_del();

 			/* Change the state of the power LED to "blink" */
 			gpio_line_set(DSMG600_LED_PWR_GPIO, IXP4XX_GPIO_LOW);
 		} else {
 			power_button_countdown = PBUTTON_HOLDDOWN_COUNT;
 		}
 	}

 	mod_timer(&dsmg600_power_timer, jiffies + msecs_to_jiffies(500));
 }

 static irqreturn_t dsmg600_reset_handler(int irq, void *dev_id)
 {
 	/* This is the paper-clip reset, it shuts the machine down directly. */
 	machine_power_off();

 	return IRQ_HANDLED;
 }

 static void __init dsmg600_timer_init(void)
 {
     /* The xtal on this machine is non-standard. */
     ixp4xx_timer_freq = DSMG600_FREQ;

     /* Call standard timer_init function. */
     ixp4xx_timer_init();
 }

 static struct sys_timer dsmg600_timer = {
     .init   = dsmg600_timer_init,
 };

 static void __init dsmg600_init(void)
 {
 	ixp4xx_sys_init();

 	/* Make sure that GPIO14 and GPIO15 are not used as clocks */
 	*IXP4XX_GPIO_GPCLKR = 0;

 	dsmg600_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
 	dsmg600_flash_resource.end =
 		IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1;

 	i2c_register_board_info(0, dsmg600_i2c_board_info,
 				ARRAY_SIZE(dsmg600_i2c_board_info));

 	/* The UART is required on the DSM-G600 (Redboot cannot use the
 	 * NIC) -- do it here so that it does *not* get removed if
 	 * platform_add_devices fails!
          */
         (void)platform_device_register(&dsmg600_uart);

 	platform_add_devices(dsmg600_devices, ARRAY_SIZE(dsmg600_devices));

 	pm_power_off = dsmg600_power_off;

 	if (request_irq(gpio_to_irq(DSMG600_RB_GPIO), &dsmg600_reset_handler,
 		IRQF_DISABLED | IRQF_TRIGGER_LOW,
 		"DSM-G600 reset button", NULL) < 0) {

 		printk(KERN_DEBUG "Reset Button IRQ %d not available\n",
 			gpio_to_irq(DSMG600_RB_GPIO));
 	}

 	/* The power button on the D-Link DSM-G600 is on GPIO 15, but
 	 * it cannot handle interrupts on that GPIO line.  So we'll
 	 * have to poll it with a kernel timer.
 	 */

 	/* Make sure that the power button GPIO is set up as an input */
 	gpio_line_config(DSMG600_PB_GPIO, IXP4XX_GPIO_IN);

 	/* Set the initial value for the power button IRQ handler */
 	power_button_countdown = PBUTTON_HOLDDOWN_COUNT;

 	mod_timer(&dsmg600_power_timer, jiffies + msecs_to_jiffies(500));
 }

 MACHINE_START(DSMG600, "D-Link DSM-G600 RevA")
 	/* Maintainer: www.nslu2-linux.org */
 	.boot_params	= 0x00000100,
 	.map_io		= ixp4xx_map_io,
 	.init_irq	= ixp4xx_init_irq,
 	.timer          = &dsmg600_timer,
 	.init_machine	= dsmg600_init,
 #if defined(CONFIG_PCI)
 	.dma_zone_size	= SZ_64M,
 #endif
 MACHINE_END
	/*
	* DSM-G600 board-setup
	*
	* Copyright (C) 2008 Rod Whitby <rod@whitby.id.au>
	* Copyright (C) 2006 Tower Technologies
	*
	* based on ixdp425-setup.c:
	* Copyright (C) 2003-2004 MontaVista Software, Inc.
	* based on nslu2-power.c:
	* Copyright (C) 2005 Tower Technologies
	* based on nslu2-io.c:
	* Copyright (C) 2004 Karen Spearel
	*
	* Author: Alessandro Zummo <a.zummo@towertech.it>
	* Author: Michael Westerhof <mwester@dls.net>
	* Author: Rod Whitby <rod@whitby.id.au>
	* Maintainers: http://www.nslu2-linux.org/
	*/

	#include <linux/irq.h>
	#include <linux/jiffies.h>
	#include <linux/timer.h>
	#include <linux/serial.h>
	#include <linux/serial_8250.h>
	#include <linux/leds.h>
	#include <linux/reboot.h>
	#include <linux/i2c.h>
	#include <linux/i2c-gpio.h>

	#include <asm/mach-types.h>
	#include <asm/mach/arch.h>
	#include <asm/mach/flash.h>
	#include <asm/mach/time.h>
	#include <asm/gpio.h>

	#define DSMG600_SDA_PIN 5
	#define DSMG600_SCL_PIN 4

	/* DSM-G600 Timer Setting */
	#define DSMG600_FREQ 66000000

	/* Buttons */
	#define DSMG600_PB_GPIO 15 /* power button */
	#define DSMG600_RB_GPIO 3 /* reset button */

	/* Power control */
	#define DSMG600_PO_GPIO 2 /* power off */

	/* LEDs */
	#define DSMG600_LED_PWR_GPIO 0
	#define DSMG600_LED_WLAN_GPIO 14

	static struct flash_platform_data dsmg600_flash_data = {
	.map_name = "cfi_probe",
	.width = 2,
	};

	static struct resource dsmg600_flash_resource = {
	.flags = IORESOURCE_MEM,
	};

	static struct platform_device dsmg600_flash = {
	.name = "IXP4XX-Flash",
	.id = 0,
	.dev.platform_data = &dsmg600_flash_data,
	.num_resources = 1,
	.resource = &dsmg600_flash_resource,
	};

	static struct i2c_gpio_platform_data dsmg600_i2c_gpio_data = {
	.sda_pin = DSMG600_SDA_PIN,
	.scl_pin = DSMG600_SCL_PIN,
	};

	static struct platform_device dsmg600_i2c_gpio = {
	.name = "i2c-gpio",
	.id = 0,
	.dev = {
	.platform_data = &dsmg600_i2c_gpio_data,
	},
	};

	static struct i2c_board_info __initdata dsmg600_i2c_board_info [] = {
	{
	I2C_BOARD_INFO("pcf8563", 0x51),
	},
	};

	static struct gpio_led dsmg600_led_pins[] = {
	{
	.name = "dsmg600:green:power",
	.gpio = DSMG600_LED_PWR_GPIO,
	},
	{
	.name = "dsmg600:green:wlan",
	.gpio = DSMG600_LED_WLAN_GPIO,
	.active_low = true,
	},
	};

	static struct gpio_led_platform_data dsmg600_led_data = {
	.num_leds = ARRAY_SIZE(dsmg600_led_pins),
	.leds = dsmg600_led_pins,
	};

	static struct platform_device dsmg600_leds = {
	.name = "leds-gpio",
	.id = -1,
	.dev.platform_data = &dsmg600_led_data,
	};

	static struct resource dsmg600_uart_resources[] = {
	{
	.start = IXP4XX_UART1_BASE_PHYS,
	.end = IXP4XX_UART1_BASE_PHYS + 0x0fff,
	.flags = IORESOURCE_MEM,
	},
	{
	.start = IXP4XX_UART2_BASE_PHYS,
	.end = IXP4XX_UART2_BASE_PHYS + 0x0fff,
	.flags = IORESOURCE_MEM,
	}
	};

	static struct plat_serial8250_port dsmg600_uart_data[] = {
	{
	.mapbase = IXP4XX_UART1_BASE_PHYS,
	.membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
	.irq = IRQ_IXP4XX_UART1,
	.flags = UPF_BOOT_AUTOCONF,
	.iotype = UPIO_MEM,
	.regshift = 2,
	.uartclk = IXP4XX_UART_XTAL,
	},
	{
	.mapbase = IXP4XX_UART2_BASE_PHYS,
	.membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
	.irq = IRQ_IXP4XX_UART2,
	.flags = UPF_BOOT_AUTOCONF,
	.iotype = UPIO_MEM,
	.regshift = 2,
	.uartclk = IXP4XX_UART_XTAL,
	},
	{ }
	};

	static struct platform_device dsmg600_uart = {
	.name = "serial8250",
	.id = PLAT8250_DEV_PLATFORM,
	.dev.platform_data = dsmg600_uart_data,
	.num_resources = ARRAY_SIZE(dsmg600_uart_resources),
	.resource = dsmg600_uart_resources,
	};

	static struct platform_device *dsmg600_devices[] __initdata = {
	&dsmg600_i2c_gpio,
	&dsmg600_flash,
	&dsmg600_leds,
	};

	static void dsmg600_power_off(void)
	{
	/* enable the pwr cntl gpio */
	gpio_line_config(DSMG600_PO_GPIO, IXP4XX_GPIO_OUT);

	/* poweroff */
	gpio_line_set(DSMG600_PO_GPIO, IXP4XX_GPIO_HIGH);
	}

	/* This is used to make sure the power-button pusher is serious. The button
	* must be held until the value of this counter reaches zero.
	*/
	static int power_button_countdown;

	/* Must hold the button down for at least this many counts to be processed */
	#define PBUTTON_HOLDDOWN_COUNT 4 /* 2 secs */

	static void dsmg600_power_handler(unsigned long data);
	static DEFINE_TIMER(dsmg600_power_timer, dsmg600_power_handler, 0, 0);

	static void dsmg600_power_handler(unsigned long data)
	{
	/* This routine is called twice per second to check the
	* state of the power button.
	*/

	if (gpio_get_value(DSMG600_PB_GPIO)) {

	/* IO Pin is 1 (button pushed) */
	if (power_button_countdown > 0)
	power_button_countdown--;

	} else {

	/* Done on button release, to allow for auto-power-on mods. */
	if (power_button_countdown == 0) {
	/* Signal init to do the ctrlaltdel action,
	* this will bypass init if it hasn't started
	* and do a kernel_restart.
	*/
	ctrl_alt_del();

	/* Change the state of the power LED to "blink" */
	gpio_line_set(DSMG600_LED_PWR_GPIO, IXP4XX_GPIO_LOW);
	} else {
	power_button_countdown = PBUTTON_HOLDDOWN_COUNT;
	}
	}

	mod_timer(&dsmg600_power_timer, jiffies + msecs_to_jiffies(500));
	}

	static irqreturn_t dsmg600_reset_handler(int irq, void *dev_id)
	{
	/* This is the paper-clip reset, it shuts the machine down directly. */
	machine_power_off();

	return IRQ_HANDLED;
	}

	static void __init dsmg600_timer_init(void)
	{
	/* The xtal on this machine is non-standard. */
	ixp4xx_timer_freq = DSMG600_FREQ;

	/* Call standard timer_init function. */
	ixp4xx_timer_init();
	}

	static struct sys_timer dsmg600_timer = {
	.init = dsmg600_timer_init,
	};

	static void __init dsmg600_init(void)
	{
	ixp4xx_sys_init();

	/* Make sure that GPIO14 and GPIO15 are not used as clocks */
	*IXP4XX_GPIO_GPCLKR = 0;

	dsmg600_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
	dsmg600_flash_resource.end =
	IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1;

	i2c_register_board_info(0, dsmg600_i2c_board_info,
	ARRAY_SIZE(dsmg600_i2c_board_info));

	/* The UART is required on the DSM-G600 (Redboot cannot use the
	* NIC) -- do it here so that it does not get removed if
	* platform_add_devices fails!
	*/
	(void)platform_device_register(&dsmg600_uart);

	platform_add_devices(dsmg600_devices, ARRAY_SIZE(dsmg600_devices));

	pm_power_off = dsmg600_power_off;

	if (request_irq(gpio_to_irq(DSMG600_RB_GPIO), &dsmg600_reset_handler,
	IRQF_DISABLED \| IRQF_TRIGGER_LOW,
	"DSM-G600 reset button", NULL) < 0) {

	printk(KERN_DEBUG "Reset Button IRQ %d not available\n",
	gpio_to_irq(DSMG600_RB_GPIO));
	}

	/* The power button on the D-Link DSM-G600 is on GPIO 15, but
	* it cannot handle interrupts on that GPIO line. So we'll
	* have to poll it with a kernel timer.
	*/

	/* Make sure that the power button GPIO is set up as an input */
	gpio_line_config(DSMG600_PB_GPIO, IXP4XX_GPIO_IN);

	/* Set the initial value for the power button IRQ handler */
	power_button_countdown = PBUTTON_HOLDDOWN_COUNT;

	mod_timer(&dsmg600_power_timer, jiffies + msecs_to_jiffies(500));
	}

	MACHINE_START(DSMG600, "D-Link DSM-G600 RevA")
	/* Maintainer: www.nslu2-linux.org */
	.boot_params = 0x00000100,
	.map_io = ixp4xx_map_io,
	.init_irq = ixp4xx_init_irq,
	.timer = &dsmg600_timer,
	.init_machine = dsmg600_init,
	#if defined(CONFIG_PCI)
	.dma_zone_size = SZ_64M,
	#endif
	MACHINE_END