| /*------------------------------------------------------------------------ |
| * smc9000.h |
| * |
| * Copyright (C) 1998 by Daniel Engström |
| * Copyright (C) 1996 by Erik Stahlman |
| * |
| * This software may be used and distributed according to the terms |
| * of the GNU Public License, incorporated herein by reference. |
| * |
| * This file contains register information and access macros for |
| * the SMC91xxx chipset. |
| * |
| * Information contained in this file was obtained from the SMC91C94 |
| * manual from SMC. To get a copy, if you really want one, you can find |
| * information under www.smsc.com in the components division. |
| * ( this thanks to advice from Donald Becker ). |
| * |
| * Authors |
| * Daniel Engström <daniel.engstrom@riksnett.no> |
| * Erik Stahlman <erik@vt.edu> |
| * |
| * History |
| * 96-01-06 Erik Stahlman moved definitions here from main .c |
| * file |
| * 96-01-19 Erik Stahlman polished this up some, and added |
| * better error handling |
| * 98-09-25 Daniel Engström adjusted for Etherboot |
| * 98-09-27 Daniel Engström moved some static strings back to the |
| * main .c file |
| * --------------------------------------------------------------------------*/ |
| #ifndef _SMC9000_H_ |
| # define _SMC9000_H_ |
| |
| /* I want some simple types */ |
| typedef unsigned char byte; |
| typedef unsigned short word; |
| typedef unsigned long int dword; |
| |
| /*--------------------------------------------------------------- |
| * |
| * A description of the SMC registers is probably in order here, |
| * although for details, the SMC datasheet is invaluable. |
| * |
| * Basically, the chip has 4 banks of registers ( 0 to 3 ), which |
| * are accessed by writing a number into the BANK_SELECT register |
| * ( I also use a SMC_SELECT_BANK macro for this ). |
| * |
| * The banks are configured so that for most purposes, bank 2 is all |
| * that is needed for simple run time tasks. |
| * ----------------------------------------------------------------------*/ |
| |
| /* |
| * Bank Select Register: |
| * |
| * yyyy yyyy 0000 00xx |
| * xx = bank number |
| * yyyy yyyy = 0x33, for identification purposes. |
| */ |
| #define BANK_SELECT 14 |
| |
| /* BANK 0 */ |
| |
| #define TCR 0 /* transmit control register */ |
| #define TCR_ENABLE 0x0001 /* if this is 1, we can transmit */ |
| #define TCR_FDUPLX 0x0800 /* receive packets sent out */ |
| #define TCR_STP_SQET 0x1000 /* stop transmitting if Signal quality error */ |
| #define TCR_MON_CNS 0x0400 /* monitors the carrier status */ |
| #define TCR_PAD_ENABLE 0x0080 /* pads short packets to 64 bytes */ |
| |
| #define TCR_CLEAR 0 /* do NOTHING */ |
| /* the normal settings for the TCR register : */ |
| #define TCR_NORMAL (TCR_ENABLE | TCR_PAD_ENABLE) |
| |
| |
| #define EPH_STATUS 2 |
| #define ES_LINK_OK 0x4000 /* is the link integrity ok ? */ |
| |
| #define RCR 4 |
| #define RCR_SOFTRESET 0x8000 /* resets the chip */ |
| #define RCR_STRIP_CRC 0x200 /* strips CRC */ |
| #define RCR_ENABLE 0x100 /* IFF this is set, we can receive packets */ |
| #define RCR_ALMUL 0x4 /* receive all multicast packets */ |
| #define RCR_PROMISC 0x2 /* enable promiscuous mode */ |
| |
| /* the normal settings for the RCR register : */ |
| #define RCR_NORMAL (RCR_STRIP_CRC | RCR_ENABLE) |
| #define RCR_CLEAR 0x0 /* set it to a base state */ |
| |
| #define COUNTER 6 |
| #define MIR 8 |
| #define MCR 10 |
| /* 12 is reserved */ |
| |
| /* BANK 1 */ |
| #define CONFIG 0 |
| #define CFG_AUI_SELECT 0x100 |
| #define BASE 2 |
| #define ADDR0 4 |
| #define ADDR1 6 |
| #define ADDR2 8 |
| #define GENERAL 10 |
| #define CONTROL 12 |
| #define CTL_POWERDOWN 0x2000 |
| #define CTL_LE_ENABLE 0x80 |
| #define CTL_CR_ENABLE 0x40 |
| #define CTL_TE_ENABLE 0x0020 |
| #define CTL_AUTO_RELEASE 0x0800 |
| #define CTL_EPROM_ACCESS 0x0003 /* high if Eprom is being read */ |
| |
| /* BANK 2 */ |
| #define MMU_CMD 0 |
| #define MC_BUSY 1 /* only readable bit in the register */ |
| #define MC_NOP 0 |
| #define MC_ALLOC 0x20 /* or with number of 256 byte packets */ |
| #define MC_RESET 0x40 |
| #define MC_REMOVE 0x60 /* remove the current rx packet */ |
| #define MC_RELEASE 0x80 /* remove and release the current rx packet */ |
| #define MC_FREEPKT 0xA0 /* Release packet in PNR register */ |
| #define MC_ENQUEUE 0xC0 /* Enqueue the packet for transmit */ |
| |
| #define PNR_ARR 2 |
| #define FIFO_PORTS 4 |
| |
| #define FP_RXEMPTY 0x8000 |
| #define FP_TXEMPTY 0x80 |
| |
| #define POINTER 6 |
| #define PTR_READ 0x2000 |
| #define PTR_RCV 0x8000 |
| #define PTR_AUTOINC 0x4000 |
| #define PTR_AUTO_INC 0x0040 |
| |
| #define DATA_1 8 |
| #define DATA_2 10 |
| #define INTERRUPT 12 |
| |
| #define INT_MASK 13 |
| #define IM_RCV_INT 0x1 |
| #define IM_TX_INT 0x2 |
| #define IM_TX_EMPTY_INT 0x4 |
| #define IM_ALLOC_INT 0x8 |
| #define IM_RX_OVRN_INT 0x10 |
| #define IM_EPH_INT 0x20 |
| #define IM_ERCV_INT 0x40 /* not on SMC9192 */ |
| |
| /* BANK 3 */ |
| #define MULTICAST1 0 |
| #define MULTICAST2 2 |
| #define MULTICAST3 4 |
| #define MULTICAST4 6 |
| #define MGMT 8 |
| #define REVISION 10 /* ( hi: chip id low: rev # ) */ |
| |
| |
| /* this is NOT on SMC9192 */ |
| #define ERCV 12 |
| |
| /* Note that 9194 and 9196 have the smame chip id, |
| * the 9196 will have revisions starting at 6 */ |
| #define CHIP_9190 3 |
| #define CHIP_9194 4 |
| #define CHIP_9195 5 |
| #define CHIP_9196 4 |
| #define CHIP_91100 7 |
| #define CHIP_91100FD 8 |
| |
| #define REV_9196 6 |
| |
| /* |
| * Transmit status bits |
| */ |
| #define TS_SUCCESS 0x0001 |
| #define TS_LOSTCAR 0x0400 |
| #define TS_LATCOL 0x0200 |
| #define TS_16COL 0x0010 |
| |
| /* |
| * Receive status bits |
| */ |
| #define RS_ALGNERR 0x8000 |
| #define RS_BADCRC 0x2000 |
| #define RS_ODDFRAME 0x1000 |
| #define RS_TOOLONG 0x0800 |
| #define RS_TOOSHORT 0x0400 |
| #define RS_MULTICAST 0x0001 |
| #define RS_ERRORS (RS_ALGNERR | RS_BADCRC | RS_TOOLONG | RS_TOOSHORT) |
| |
| |
| /*------------------------------------------------------------------------- |
| * I define some macros to make it easier to do somewhat common |
| * or slightly complicated, repeated tasks. |
| --------------------------------------------------------------------------*/ |
| |
| /* select a register bank, 0 to 3 */ |
| |
| #define SMC_SELECT_BANK(x, y) { _outw( y, x + BANK_SELECT ); } |
| |
| /* define a small delay for the reset */ |
| #define SMC_DELAY(x) { inw( x + RCR );\ |
| inw( x + RCR );\ |
| inw( x + RCR ); } |
| |
| |
| #endif /* _SMC_9000_H_ */ |
| |
