| #!/bin/sh |
| |
| # Bootlevels |
| # 1 - start only inetd 0000 0001 |
| # 2 - load mav80211 0000 0010 |
| # 4 - load driver 0000 0100 |
| # 8 - up dev, load wpa_supplicant 0000 1000 |
| # 16 - Settings for Android 0001 0000 |
| # 32 - running AP 0010 0000 |
| # 64 - 1-command calibration 0100 0000 |
| |
| go_version="0.91" |
| usage() |
| { |
| echo -e "\tUSAGE:\n\t `basename $0` <option> [value]" |
| echo -e "\t\t-b <value> - bootlevel, where\n\t\t\t7-PLT boot" |
| echo -e "\t\t\t15-full boot" |
| echo -e "\t\t-c <path to INI file> [path to install NVS] -" \ |
| "run calibration" |
| echo -e "\t\t-c2 <path to INI file> <path to INI file> -" \ |
| "run calibration with 2 FEMs" |
| echo -e "\t\t\twhere the default value for install path is " |
| echo -e "\t\t\t/lib/firmware/ti-connectivity/wl1271-nvs.bin" |
| echo -e "\t\t-d <value> - debuglevel, where" |
| echo -e "\t\t\t -1 - shows current value |
| \t\t\tDEBUG_IRQ = BIT(0) |
| \t\t\tDEBUG_SPI = BIT(1) |
| \t\t\tDEBUG_BOOT = BIT(2) |
| \t\t\tDEBUG_MAILBOX = BIT(3) |
| \t\t\tDEBUG_TESTMODE = BIT(4) |
| \t\t\tDEBUG_EVENT = BIT(5) |
| \t\t\tDEBUG_TX = BIT(6) |
| \t\t\tDEBUG_RX = BIT(7) |
| \t\t\tDEBUG_SCAN = BIT(8) |
| \t\t\tDEBUG_CRYPT = BIT(9) |
| \t\t\tDEBUG_PSM = BIT(10) |
| \t\t\tDEBUG_MAC80211 = BIT(11) |
| \t\t\tDEBUG_CMD = BIT(12) |
| \t\t\tDEBUG_ACX = BIT(13) |
| \t\t\tDEBUG_SDIO = BIT(14) |
| \t\t\tDEBUG_FILTERS = BIT(15) |
| \t\t\tDEBUG_ADHOC = BIT(16) |
| \t\t\tDEBUG_ALL = ~0" |
| echo -e "\t\t-m <value> - set MAC address" |
| echo -e "\t\t-ip [value] - set IP address" |
| echo -e "\t\t-v - get script version" |
| echo -e "\t\t-h - get this help" |
| } |
| |
| i=0 |
| nbr_args=$# |
| bootlevel=0 |
| dbg_lvl=0 |
| ref_clk=0 |
| mac_addr="08:00:28:90:64:31" |
| ip_addr="192.168.1.1" |
| set_ip_addr=0 |
| have_path_to_ini=0 |
| path_to_ini="" |
| path_to_ini2="" |
| have_path_to_install=0 |
| path_to_install="/lib/firmware/ti-connectivity/wl1271-nvs.bin" |
| is_android=0 |
| prefix_path2modules= |
| while [ "$i" -lt "$nbr_args" ] |
| do |
| case $1 in |
| -b) bootlevel=$2 |
| nbr_args=`expr $nbr_args - 1` |
| shift |
| ;; |
| #-r) ref_clk=$2 |
| #nbr_args=`expr $nbr_args - 1` |
| #shift |
| #;; |
| -c) |
| if [ "$nbr_args" -lt "2" ]; then |
| echo -e "missing arguments" |
| exit 1 |
| fi |
| |
| bootlevel=66 |
| have_path_to_ini=`expr $have_path_to_ini + 1` |
| path_to_ini=$2 |
| if [ "$nbr_args" -eq "2" ]; then |
| echo -e " The install path not provided" |
| echo -e " Use default ($path_to_install)" |
| nbr_args=`expr $nbr_args - 1` |
| shift |
| break |
| fi |
| |
| have_path_to_install=`expr $have_path_to_install + 1` |
| path_to_install=$3 |
| nbr_args=`expr $nbr_args - 2` |
| shift |
| shift |
| ;; |
| -c2) # calibration with 2 FEMs |
| if [ "$nbr_args" -lt "3" ]; then |
| echo -e "missing arguments" |
| exit 1 |
| fi |
| |
| bootlevel=34 |
| have_path_to_ini=`expr $have_path_to_ini + 1` |
| path_to_ini=$2 |
| path_to_ini2=$3 |
| nbr_args=`expr $nbr_args - 2` |
| shift |
| shift |
| ;; |
| -d) dbg_lvl=$2 |
| nbr_args=`expr $nbr_args - 1` |
| shift |
| ;; |
| -m) mac_addr=$2 |
| nbr_args=`expr $nbr_args - 1` |
| shift |
| ;; |
| -ip) set_ip_addr=`expr $set_ip_addr + 1` |
| case $2 in |
| "") echo -e "using default ip address" |
| ;; |
| -*) echo -e "this is another option" |
| ;; |
| *) ip_addr=$2 |
| nbr_args=`expr $nbr_args - 1` |
| shift |
| ;; |
| esac |
| ;; |
| -ini) |
| have_path_to_ini=`expr $have_path_to_ini + 1` |
| path_to_ini=$2 |
| nbr_args=`expr $nbr_args - 1` |
| shift |
| ;; |
| -v) |
| echo -e "\tgo.sh version $go_version" |
| ;; |
| -h) usage |
| exit 0 |
| ;; |
| *) echo -e "\tNothing to do" |
| ;; |
| esac |
| i=`expr $i + 1` |
| shift |
| done |
| |
| stage_uno=0 |
| stage_due=0 |
| stage_quattro=0 |
| stage_otto=0 |
| stage_sedici=0 |
| stage_trentadue=0 |
| stage_sessanta_quattro=0 |
| case $bootlevel in |
| 1) stage_uno=`expr $stage_uno + 1` |
| ;; |
| 2) stage_due=`expr $stage_due + 1` |
| ;; |
| 3) stage_uno=`expr $stage_uno + 1` |
| stage_due=`expr $stage_due + 1` |
| ;; |
| 4) stage_quattro=`expr $stage_quattro + 1` |
| ;; |
| 5) stage_uno=`expr $stage_uno + 1` |
| stage_quattro=`expr $stage_quattro + 1` |
| ;; |
| 6) stage_due=`expr $stage_due + 1` |
| stage_quattro=`expr $stage_quattro + 1` |
| ;; |
| 7) stage_uno=`expr $stage_uno + 1` |
| stage_due=`expr $stage_due + 1` |
| stage_quattro=`expr $stage_quattro + 1` |
| ;; |
| 8) stage_otto=`expr $stage_otto + 1` |
| ;; |
| 12) stage_quattro=`expr $stage_quattro + 1` |
| stage_otto=`expr $stage_otto + 1` |
| ;; |
| 15) stage_uno=`expr $stage_uno + 1` |
| stage_due=`expr $stage_due + 1` |
| stage_quattro=`expr $stage_quattro + 1` |
| stage_otto=`expr $stage_otto + 1` |
| ;; |
| 16) stage_sedici=`expr $stage_sedici + 1` |
| ;; |
| 32) stage_trentadue=`expr $stage_trentadue + 1` |
| ;; |
| 34) |
| stage_due=`expr $stage_due + 1` |
| stage_trentadue=`expr $stage_trentadue + 1` |
| ;; |
| 64) stage_sessanta_quattro=`expr $stage_sessanta_quattro + 1` |
| ;; |
| 66) |
| stage_due=`expr $stage_due + 1` |
| stage_sessanta_quattro=`expr $stage_sessanta_quattro + 1` |
| ;; |
| esac |
| |
| echo -e "\t------------ ------------\n" |
| echo -e "\t---===<<<((( WELCOME )))>>>===---\n" |
| echo -e "\t------------ ------------\n" |
| |
| insmod_path= |
| rmmod_path= |
| |
| if [ $ANDROID_ROOT ]; then |
| is_android=`expr $is_android + 1` |
| prefix_path2modules="/system/" |
| insmod_path="/system/bin/" |
| rmmod_path="/system/bin/" |
| fi |
| |
| if [ "$stage_uno" -ne "0" ]; then |
| echo -e "+++ Mount the debugfs on /sys/kernel/debug" |
| |
| echo 8 > /proc/sys/kernel/printk |
| |
| if [ -e /libexec/inetd ]; then |
| /libexec/inetd /etc/inetd.conf & |
| fi |
| |
| if [ ! -e /sys/kernel/debug/tracing ]; then |
| mount -t debugfs none /sys/kernel/debug/ |
| fi |
| fi |
| |
| if [ "$stage_due" -ne "0" ]; then |
| echo -e "+++ Load mac80211, cfg80211, crc7 and firmware_class" |
| |
| run_it=`cat /proc/modules | grep "cfg80211"` |
| if [ "$run_it" == "" ]; then |
| "$insmod_path"insmod /lib/modules/`uname -r`/kernel/net/wireless/cfg80211.ko |
| fi |
| run_it=`cat /proc/modules | grep "mac80211"` |
| if [ "$run_it" == "" ]; then |
| insmod /lib/modules/`uname -r`/kernel/net/mac80211/mac80211.ko |
| fi |
| run_it=`cat /proc/modules | grep "crc7"` |
| if [ "$run_it" == "" ]; then |
| insmod /lib/modules/`uname -r`/kernel/lib/crc7.ko |
| fi |
| run_it=`cat /proc/modules | grep "firmware_class"` |
| if [ "$run_it" == "" ]; then |
| insmod /lib/modules/`uname -r`/kernel/drivers/base/firmware_class.ko |
| fi |
| fi |
| |
| if [ "$stage_quattro" -ne "0" ]; then |
| echo -e "+++ Load wl12xx driver, enable mac80211 tracing" |
| |
| run_it=`cat /proc/modules | grep "wl12xx"` |
| if [ "$run_it" == "" ]; then |
| if [ "$is_android" -eq "0" ]; then |
| "$insmod_path"insmod /lib/modules/`uname -r`/kernel/drivers/net/wireless/wl12xx/wl12xx.ko |
| else |
| "$insmod_path"insmod /system/lib/modules/wl12xx.ko |
| fi |
| if [ "$?" != "0" ]; then |
| echo -e "Fail to load wl12xx" |
| exit 1 |
| fi |
| fi |
| |
| run_it=`cat /proc/modules | grep "wl12xx_sdio"` |
| if [ "$run_it" == "" ]; then |
| if [ "$is_android" -eq "0" ]; then |
| "$insmod_path"insmod /lib/modules/`uname -r`/kernel/drivers/net/wireless/wl12xx/wl12xx_sdio.ko |
| else |
| insmod /system/lib/modules/wl12xx_sdio.ko |
| fi |
| if [ "$?" != "0" ]; then |
| echo -e "Fail to load wl12xx_sdio" |
| exit 1 |
| fi |
| fi |
| |
| sleep 1 |
| if [ -e /sys/kernel/debug/tracing ]; then |
| echo 1 > /sys/kernel/debug/tracing/events/mac80211/enable |
| fi |
| |
| #ifconfig wlan0 hw ether $mac_addr |
| #cat /sys/kernel/debug/mmc2/ios |
| fi |
| |
| if [ "$stage_otto" -ne "0" ]; then |
| echo -e "+++ Start interface, enable monitoring events, run wpa_supplicant" |
| |
| ifconfig wlan0 up |
| if [ "$?" != "0" ]; then |
| echo -e "Fail to start iface" |
| exit 1 |
| fi |
| |
| sleep 1 |
| iw event > /var/log/iwevents & |
| |
| #wpa_supplicant -P/var/run/wpa_supplicant.pid -iwlan0 |
| # -c/etc/wpa_supplicant.conf -Dnl80211 -f/var/log/wpa_supplicant.log & |
| #iw wlan0 cqm rssi -55 2 |
| #wpa_supplicant -ddt -iwlan0 -c/etc/wpa_supplicant.conf -Dnl80211 -f/var/log/wpa.log & |
| wpa_supplicant -iwlan0 -c/etc/wpa_supplicant.conf -Dnl80211 & |
| #python /usr/share/peripherals-test-autom/dut.py -v & |
| fi |
| |
| if [ "$stage_sedici" -ne "0" ]; then |
| echo manual_lock > /sys/power/wake_lock |
| echo performance > /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor |
| echo 1 > /sys/devices/system/cpu/cpu1/online |
| echo performance > /sys/devices/system/cpu/cpu1/cpufreq/scaling_governor |
| fi |
| |
| if [ "$stage_trentadue" -ne "0" ]; then |
| |
| if [ "$have_path_to_ini" -eq "0" ]; then |
| echo -e "Missing ini file parameter" |
| exit 1 |
| fi |
| |
| # 1. unload wl12xx kernel modules |
| echo -e "+++ Unload wl12xx driver" |
| run_it=`cat /proc/modules | grep "wl12xx_sdio"` |
| if [ "$run_it" != "" ]; then |
| rmmod wl12xx_sdio |
| fi |
| run_it=`cat /proc/modules | grep "wl12xx"` |
| if [ "$run_it" != "" ]; then |
| rmmod wl12xx |
| fi |
| |
| # 2. create reference NVS file with default MAC |
| echo -e "+++ Create reference NVS with $path_to_ini $path_to_ini2" |
| ./calibrator set ref_nvs2 $path_to_ini $path_to_ini2 |
| if [ "$?" != "0" ]; then |
| echo -e "Fail to tune channel" |
| exit 1 |
| fi |
| |
| # 3. Set AutoFEM detection to auto |
| echo -e "+++ Set Auto FEM detection to auto" |
| run_it=`./calibrator set nvs_autofem 1 ./new-nvs.bin` |
| |
| # 4. copy NVS to proper place |
| echo -e "+++ Copy reference NVS file to $path_to_install" |
| run_it=`cp -f ./new-nvs.bin $path_to_install` |
| |
| # 5. load wl12xx kernel modules |
| sh $0 -b 4 |
| |
| # 6. calibrate |
| echo -e "+++ Calibrate" |
| ./calibrator wlan0 plt power_mode on |
| if [ "$?" != "0" ]; then |
| echo -e "Fail to set power mode to on" |
| exit 1 |
| fi |
| |
| ./calibrator wlan0 plt tune_channel 0 7 |
| if [ "$?" != "0" ]; then |
| echo -e "Fail to tune channel" |
| exit 1 |
| fi |
| |
| run_it=`cat $path_to_ini | grep "RxTraceInsertionLoss_5G"` |
| if [ "$run_it" != "" ]; then |
| ./calibrator wlan0 plt tx_bip 1 1 1 1 1 1 1 1 $path_to_install |
| if [ "$?" != "0" ]; then |
| echo -e "Fail to calibrate" |
| exit 1 |
| fi |
| else |
| ./calibrator wlan0 plt tx_bip 1 0 0 0 0 0 0 0 $path_to_install |
| if [ "$?" != "0" ]; then |
| echo -e "Fail to calibrate" |
| exit 1 |
| fi |
| fi |
| |
| ./calibrator wlan0 plt power_mode off |
| if [ "$?" != "0" ]; then |
| echo -e "Fail to set power mode to off" |
| exit 1 |
| fi |
| |
| # 7. unload wl12xx kernel modules |
| rmmod wl12xx_sdio wl12xx |
| |
| # 8. update NVS file with random and valid MAC address |
| echo -e "+++ Update NVS file with random valid MAC address" |
| ./calibrator set nvs_mac ./new-nvs.bin |
| if [ "$?" != "0" ]; then |
| echo -e "Fail to set NVS MAC address" |
| exit 1 |
| fi |
| |
| # 9. copy calibrated NVS file to proper place |
| echo -e "+++ Copy calibrated NVS file to $path_to_install" |
| run_it=`cp -f ./new-nvs.bin $path_to_install` |
| |
| # 10. load wl12xx kernel modules |
| if [ ! -e /sys/kernel/debug/tracing ]; then |
| mount -t debugfs none /sys/kernel/debug/ |
| fi |
| sh $0 -b 4 |
| |
| echo -e "\n\tDear Customer, you are ready to use our calibrated device\n" |
| fi |
| |
| # |
| # 1-command calibration |
| # parameters are INI file, path where to install NVS (default /lib/firmware) |
| # |
| |
| if [ "$stage_sessanta_quattro" -ne "0" ]; then |
| |
| if [ "$have_path_to_ini" -eq "0" ]; then |
| echo -e "Missing ini file parameter" |
| exit 1 |
| fi |
| |
| # 1. unload wl12xx kernel modules |
| echo -e "+++ Unload wl12xx driver" |
| run_it=`cat /proc/modules | grep "wl12xx_sdio"` |
| if [ "$run_it" != "" ]; then |
| rmmod wl12xx_sdio |
| fi |
| run_it=`cat /proc/modules | grep "wl12xx"` |
| if [ "$run_it" != "" ]; then |
| rmmod wl12xx |
| fi |
| |
| # 2. create reference NVS file with default MAC |
| echo -e "+++ Create reference NVS with INI $path_to_ini" |
| ./calibrator set ref_nvs $path_to_ini |
| if [ "$?" != "0" ]; then |
| echo -e "Fail to tune channel" |
| exit 1 |
| fi |
| |
| # 3. copy NVS to proper place |
| echo -e "+++ Copy reference NVS file to $path_to_install" |
| run_it=`cp -f ./new-nvs.bin $path_to_install` |
| |
| # 4. load wl12xx kernel modules |
| sh $0 -b 4 |
| |
| # 5. calibrate |
| echo -e "+++ Calibrate" |
| ./calibrator wlan0 plt power_mode on |
| if [ "$?" != "0" ]; then |
| echo -e "Fail to set power mode to on" |
| exit 1 |
| fi |
| |
| ./calibrator wlan0 plt tune_channel 0 7 |
| if [ "$?" != "0" ]; then |
| echo -e "Fail to tune channel" |
| exit 1 |
| fi |
| |
| run_it=`cat $path_to_ini | grep "RxTraceInsertionLoss_5G"` |
| if [ "$run_it" != "" ]; then |
| ./calibrator wlan0 plt tx_bip 1 1 1 1 1 1 1 1 $path_to_install |
| if [ "$?" != "0" ]; then |
| echo -e "Fail to calibrate" |
| exit 1 |
| fi |
| else |
| ./calibrator wlan0 plt tx_bip 1 0 0 0 0 0 0 0 $path_to_install |
| if [ "$?" != "0" ]; then |
| echo -e "Fail to calibrate" |
| exit 1 |
| fi |
| fi |
| |
| ./calibrator wlan0 plt power_mode off |
| if [ "$?" != "0" ]; then |
| echo -e "Fail to set power mode to off" |
| exit 1 |
| fi |
| |
| # 6. unload wl12xx kernel modules |
| rmmod wl12xx_sdio wl12xx |
| |
| # 7. update NVS file with random and valid MAC address |
| echo -e "+++ Update NVS file with random valid MAC address" |
| ./calibrator set nvs_mac ./new-nvs.bin |
| if [ "$?" != "0" ]; then |
| echo -e "Fail to set NVS MAC address" |
| exit 1 |
| fi |
| |
| # 8. copy calibrated NVS file to proper place |
| echo -e "+++ Copy calibrated NVS file to $path_to_install" |
| run_it=`cp -f ./new-nvs.bin $path_to_install` |
| |
| # 9. load wl12xx kernel modules |
| if [ ! -e /sys/kernel/debug/tracing ]; then |
| mount -t debugfs none /sys/kernel/debug/ |
| fi |
| sh $0 -b 4 |
| |
| echo -e "\n\tDear Customer, you are ready to use our calibrated device\n" |
| fi |
| |
| if [ "$dbg_lvl" -eq "-1" ] && [ -e /sys/module/wl12xx/parameters/debug_level ]; then |
| dbg_lvl=`cat /sys/module/wl12xx/parameters/debug_level` |
| echo -e "\ndbg lvl: $dbg_lvl\n" |
| elif [ "$dbg_lvl" -ne "0" ] && [ -e /sys/module/wl12xx/parameters/debug_level ]; then |
| echo "$dbg_lvl" > /sys/module/wl12xx/parameters/debug_level |
| |
| echo 'module cfg80211 +p' > /sys/kernel/debug/dynamic_debug/control |
| echo 'module mac80211 +p' > /sys/kernel/debug/dynamic_debug/control |
| echo 'module wl12xx +p' > /sys/kernel/debug/dynamic_debug/control |
| echo 'module wl12xx_sdio +p' > /sys/kernel/debug/dynamic_debug/control |
| fi |
| |
| if [ "$set_ip_addr" -ne "0" ]; then |
| echo -e "Going to set IP $ip_addr" |
| ifconfig wlan0 $ip_addr up |
| fi |
| |
| exit 0 |
